Miele G 879 SCVI Скачать руководство пользователя страница 24

Страница: 24 / 76

Adjusting the upper basket.

(depending on model)

The upper basket height is adjustable.
If tall items of dishware are being
washed, more room can be obtained
by raising or lowering the upper basket.

Pull out the upper basket and loosen
the two locknuts on either side of the
basket.

Adjust the basket up or down to the
desired height.

Tighten the locknuts.

The upper basket can also be set on
an angle, with one side high, and the
other side low. Ensure however that the
basket can be inserted smoothly into
the cabinet.

Depending on the setting of the upper
basket, the following dishware dimen-
sions can be accommodated:

Upper

basket

position

Upper

basket

diameter

Lower

basket

diameter

Top

20.5 cm

(8")

30 cm

(12")

Middle

22.5 cm

(9")

28 cm

(11")

Bottom

24.5 cm

(9 1/2")

26 cm

(10")

Loading the dishwasher

Содержание G 879 SCVI













































































Результаты поиска

Содержание G 879 SCVI

Отзывы:

Похожие инструкции для G 879 SCVI

Бренды по названию

Популярные бренды

Miele G 879 SCVI, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание G 879 SCVI

Отзывы:

Похожие инструкции для G 879 SCVI

Бренды по названию

Популярные бренды