Miele G 685 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 88

background image

Installing a freestanding dishwasher

Adapting the height of the decor
panel supplied

Mark the measurement "X" on the left
and right hand side of the decor
panel and on the decor frame strips.

Take off and shorten the decor frame
strips (see Step 2), the decor panel
and the packing card.

Establishing the height of a new
decor panel

The decor panel supplied with the dish-
washer can be exchanged for a panel
to match your kitchen decor.

The new panel must have the following
measurements:

Width:
587 mm

Thickness:
Minimum 1 mm and maximum 4 mm.
The packing card originally supplied
behind the decor panel must be
removed for new panels with a thick-
ness of more than 2 mm.

Height:
604 mm minus "

X

" mm

Mark the measurement "

X

" on the left

and right hand side of the decor
frame.

Take off the decor frame strips (see
Step 2), the decor panel and the
packing card, and shorten the decor
frame strips, and the packing card (if
used).

Installing a freestanding dishwasher

61

«
...
59
60
61
62
63
...
»

Содержание G 685

























































































Отзывы:

Нет отзывов

Похожие инструкции для G 685

Upright Door Dishmachines Tempstar Series

Бренд: Jackson Страницы: 103

Бренд: GE Страницы: 72

Бренд: Saba Страницы: 39

Бренд: Unimac Страницы: 4

Бренд: Bauknecht Страницы: 14

Бренд: Omega Страницы: 31

Бренд: Hanseatic Страницы: 78

Бренд: montpellier Страницы: 24

Бренд: BALAY Страницы: 26

Бренд: Kuppersbusch Страницы: 28

Бренд: John Lewis Страницы: 36

Бренд: Beko Страницы: 40

Бренд: Beko Страницы: 40

Бренд: Beko Страницы: 40

Бренд: Beko Страницы: 28

Бренд: Beko Страницы: 48

Бренд: Beko Страницы: 44

Бренд: Beko Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды