Miele DA 3566 Скачать руководство пользователя страница 15

Modes of operation

15

Con@ctivity 2.0 function

Automatic control
The cooker hood has a communication

facility which enables the automatic op‐

eration of the cooker hood depending

on the operational state of the hob.

To make use of the communication fa‐

cility, the hob must be fitted with a

Con@ctivity 2.0 Stick 

.

Please refer to the installation instruc‐

tions for the Con@ctivity 2.0 stick to

check whether it is compatible with

your hob.
To use the Con@ctivity 2.0 function, a

wireless connection must be establish‐

ed between the hob and the cooker

hood (see "Activating Con@ctivity 2.0).

The hob transmits information about its

operational status via a wireless signal

to the cooker hood.

– The hob lighting will switch on auto‐

matically.

– With the deflector plate pulled out,

during cooking, the cooker hood au‐

tomatically sets the power level ac‐

cording to the number of cooking

zones in operation and their power

levels.

– After the hob has been switched off,

the cooker hood fan and the hob

lighting will switch off automatically.

See "Operation" for detailed informa‐

tion about this function.

Содержание DA 3566

























































Отзывы: