Midland ProLine PL5161 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 37

Midland ProLine PL5161 Скачать руководство пользователя страница 9

9

VI.3

INSTALLING THE ANTENNA

Screw the antenna into the connector on the top of the radio by holding the antenna at its base and turning it

clockwise

until seated. Do not overtighten.

The antenna should never be used to carry your radio, or as a base to clip radio accessories. Misuse of the antenna
can cause damage, and reduce your radio’s performance.

VI.4 INSTALLING THE BELT CLIP

We recommend that the belt clip is installed on the radio. It keeps the radio from coming in contact with hot
surfaces, and away from your body if heat build-up occurs with excess transmissions.

Use the two supplied screws to install the belt clip. If a replacement is needed, use a screw designed to the exact
specifications as the original, to prevent accidental contact with internal circuitry, or possible personal injury. Never

use

glue in conjunction with the provided screws. Some of the glue's components may crack the radio back panel

causing radio damage and possible personal injury.

VI.5

INSTALLING THE SPEAKER MICROPHONE JACK COVER

If you are not using an accessory, install the provided cover over the speaker microphone jack using the screw
supplied. This will keep the radio water resistant.

VI.6

ATTACHING THE OPTIONAL SPEAKER MICROPHONE

1. Insert the speaker microphone jack into the radio.
2. Use the thumbscrew attachment on the speaker microphone to make connection to the radio.

NOTE:

The radio is not fully water resistant while the speaker microphone is attached.

«
...
7
8
9
10
11
...
»

Содержание ProLine PL5161






































Отзывы:

Нет отзывов