background image

3

ENGLISH

1. ABOVE ALL... SAFETY!

1.1 Symbols used

For ease and convenience of viewing, 

NEPTUNE 100

 uses symbols to highlight urgent situations, 

practical advice, and general information. 

Warnings such as this, shown using an open hand symbol, indicate a crucial description 

 

regarding  technical  repairs,  dangerous  conditions,  safety  warnings,  advice  and/or 

important information.  Ignoring these symbols may result in serious problems and/or 

damage and/or personal injury.

Notes such as this one indicate practical advice that we suggest be followed for optimal

 

performance with 

NEptuNE 100.

1.2 Warnings

1.2.a General 

This device has been tested for compliance with Class D digital marine device limits.  These 

 

limits were created to allow for reasonable protection against damaging interference.

This device is to be used solely as an aid to navigation.  Its settings may be influenced by 

 

diverse factors, such as defects or malfunction of the device, environmental conditions 

or improper use.

It  is  the  user’s  responsibility  to  observe  reasonable  prudence  and  judgement  in 

 

navigation,  and  as  such  this  device  should  not  be  considered  a  substitute  for  this 

reasonable prudence and judgement.

Do not open the radio for any reason!  NEPTUNE 100’s precision mechanics and electronics 

 

require  expertise  and  specialized  equipment;  for  the  same  reason,  the  radio  should 

under  no  circumstances  be  realigned  as  it  has  already  been  calibrated  for  maximum 

performance.  Unauthorized opening of the transceiver will nullify the warranty.

1.2.b Radiofrequency/installation

Midland  recommends  following  the  requirements  for  prevention  of  radiofrequency 

 

exposure.  Unauthorized  changes  or  modifications  to  this  device  may  invalidate 

conformity to the ETSI Regulations. 

This  VHF  DSC  transceiver  generates  and  irradiates  electromagnetic  energy  (EME)  at 

 

radiofrequency (RF), and as such must be installed and placed in operating conditions 

that are in conformity with the instructions contained in this manual and with current 

regulations. Not following these instructions can cause personal injury and/or malfunction 

of the device.

Do not use NEPTUNE 100 before connecting a suitable antenna that is in perfect working 

 

condition – although NEPTUNE 100 is protected, this may seriously damage the stages 

of transmission power.

Do  not  use  transmit  before  ensuring  proper  connection  of  the  antenna.    During 

 

transmission, remain at a minimum distance of 1mt from the antenna.

1.2.c Automatic Transmitter  Identification System (ATIS)

Your marine transceiver may activate, if necessary, the ATIS function.  The ATIS function 

 

may  be  activated  when  using  the  transceiver  within  the  internal  navigable  waters  of 

Europe which require the automatic transmission of identification.  For further details, 

please contact your local authorities.

Содержание NEPTUNE 100






























Отзывы: