background image

11

Duplex Operation

 

Duplex operation allows the radio to transmit on a different frequency to that which it receives 

allowing operation through repeater stations. Repeaters automatically retransmit your signal over a 

wider area providing greatly increased range. Duplex operates only on channels 1-8 & 41-48. When 

duplex is selected on these channels, the radio receives on that channel but actually transmits 30 

channels higher.

Channel Selecting 

1  2  3  4  5*  6  7  8 

Receiving Channel 

1  2  3  4  5*  6  7  8 

Transmitting Channel 

31  32  33  34  35*  36  37  38 

Channel Selecting 

41  42  43  44  45*  46  47  48

Receiving Channel 

41  42  43  44  45*  46  47  48

Transmitting Channel 

71  72  73  74  75*  76  77  78

* Channel only for Emergency.

ML801 allows you to choose channel duplex operation.

To select Duplex on individual channels

1. Select the required channel (1-8 or 41-48) 

Switch the MENU to F4, press menu to confirm, then press       or      to select which channel to 

enable/disable duplex.

Press menu and then press V+ or V- key. The “o” in the channel number will change to “r”  

Eg: Channel 2 will be displayed as “02” when in simplex mode but will change to “r2” when duplex 

is activated on that channel. Channel 42 will be displayed as “42” when in simplex mode but will 

change to “u2” when duplex is activated on that channel. 

Note: Channel 1-8 displays “r1-r8” after setting Duplex. Channel 41-48 displays  “1r-8r” after  

setting duplex.

Widen Frequency for Receiving 

 

If users need wider receiving frequencies, these can be added by an authorised Midland Dealer.  

Note: The widened frequency is only for receiving use.

Adjusting the beep tone level 

 

The beep tone is designed to provide audible feedback whenever a key is pressed. If the beep tone 

level is too loud or too soft for your operating environment you can adjust it as follows:  

1. Switch the MENU to F5, press menu again, then press       or      to enter choice.

2. A number will flash on the display to indicate the current beep tone level setting.

3. Press       or       to increase or decrease the beep level. The maximum level is B8 and the minimum 

audible level is B1. To turn the beep tone off set the level to B0.

4. To return the radio to normal operation, press MENU key or simply wait 3 seconds.

 

Содержание ML801

















Отзывы: