Midea DSK38P5 Скачать руководство пользователя страница 6

Страница: 6 / 12

3.1 Installation Instruction

3.2 Power Cord Installation

Check the capacity of power circuit;
Power cord installation;
Water heater installation;
Plumbing connection;
Power supply connection;

①
②
③
④
⑤

Water Supply.

Step 1

Step 2

⑥

3. UNIT INSTALLATION

Remove the screws at the bottom of the unit. Lift

up the Main Switch Knob and Power Knob to

make it free. Remove the front plate gently.

Remove the power cord wire pressing plate and

keep the screws.

Step 3

Step 4

Step 5

Step 6

Gash the middle of the film of the power cord

jacket with a sharp knife in order to put into

power lines.

Tighten the wire-pressing plate with screws to

primary position, ensure that the power cord not

be pulled out more than 60N.

Screw the power cord into the jacket for

installation of wire pressing plate.

Connect the power cord to wiring terminals; the

method is as shown in picture.

Содержание DSK38P5













Результаты поиска

Содержание DSK38P5

Отзывы:

Бренды по названию

Популярные бренды

Midea DSK38P5, Инструкция по эксплуатации

Результаты поиска

Содержание DSK38P5

Отзывы:

Бренды по названию

Популярные бренды