Middleby Marshall CTX DZ26T Domestic страница 9 Скачать руководство пользователя

Страница: 9 / 62

SECTION 2

INSTALLATION

SECTION 2

INSTALLATION

WARNING

Keep the appliance area free and clear of

combustibles.

WARNING

The oven must be installed on an even (level)

non-flammable flooring and any adjacent walls

must not be flammable. Recommended

minimum clearances are specified in the

Description section of this manual.

WARNING

Do not obstruct the flow of ventilation air to and

from your oven. There must be no obstruction

around or underneath the oven. Constructional

changes to the area where the oven is installed

shall not affect the air supply to the oven.

CAUTION

To reduce the risk of fire, the appliance is to be

mounted on floors of noncombustible

construction with noncombustible flooring and

surface finish and with no combustible material

against the underside thereof, or on

noncombustible slabs or arches having no

combustible material against the underside

thereof. Such construction shall in all cases

extend not less than 12 inches (304mm) beyond

the equipment on all sides.

NOTICE

For additional installation information, contact your

local Authorized Service Agent.

NOTICE

There must be adequate clearance between the

oven and combustible construction. Clearance must

also be provided for servicing and for proper

operation.

IMPORTANT

An electrical wiring diagram for the oven is located

inside the control compartment.

NOTE:

All aspects of the oven installation, including

placement, utility connections, and ventilation

requirements, must conform with any applicable local,

national, or international codes. These codes

supersede the requirements and guidelines provided

in this manual.

NOTE:

In the USA, the oven installation must conform

to local codes. Electric ovens, when installed, must be

electrically grounded in accordance with local codes,

or in the absence of local codes, with the National

Electrical Code (NEC), or ANSI/NFPA 70.

NOTE:

In Canada, the oven installation must conform

with local codes. Electric ovens, when installed, must

be electrically grounded in accordance with local

codes, or in the absence of local codes, with Canadian

Electrical Code, CSA C22.2.

CAUTION

It is recommended that the oven be placed

under a ventilation hood for adequate air supply

and ventilation.

Содержание CTX DZ26T Domestic































































Результаты поиска

Содержание CTX DZ26T Domestic

Отзывы:

Похожие инструкции для CTX DZ26T Domestic

Бренды по названию

Популярные бренды

Middleby Marshall CTX DZ26T Domestic, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание CTX DZ26T Domestic

Отзывы:

Похожие инструкции для CTX DZ26T Domestic

Бренды по названию

Популярные бренды