58
Chapter 7: Output Section
VeniceF
Operator Manual
FireWire
The
FireWire
section is located on the rear panel of the console.
FireWire section on the rear panel
The output section on the control surface has a
firewire output select
section that
lets you replace the FireWire outputs of the dual stereo input channels, and route
output buses to the FireWire interface instead.
Item
Description
1
Meter LEDs
These LEDs comprise the group meter, which monitors the
signal level of the group bus. Range is from -12dBu to +18dBu (3dBu steps
from -12dBu to 0dBu, and 6dBu steps from 0dBu to +18dBu).
2
aux c/o switch
See “Group-aux changeover” on page 56.
3
mono switch
This switch routes the channel signal to the mono bus
(post-EQ, post-mute and post-fader).
4
stereo switch
Routes the channel signal to the stereo master bus
(post-EQ, post-pan, post-mute and post-fader).
5
pan control knob
The pan control allows the group channel signal to be
positioned in a stereo field when routed to the stereo master bus. The pan
control allows continuous adjustment of the image from hard left, to hard
right with a centre detent, and obeys a constant power law (that is, -3dB at
the centre).
6
MUTE switch and red LED
The
MUTE
switch mutes the channel signal.
Note that the signal will still be sent to the insert point. The mute LED
illuminates to show that the mute is on.
7
SOLO switch and yellow LED
Group output solo has the same function
as on the mono input channels (see “Pan, routing, mute and solo” on
page 39).
8
Fader
The group fader allows for continuous adjustment of the channel
level from
4
(infinity/off) to +10dB.
Item
Description
1
FireWire socket
For connecting a FireWire 400, 6-pin connector (to IEEE
1394 standard) to a PC.
2
sample rate LEDs
There are two possible sample rate frequencies (in
Hz), which are configured via a PC using the FireWire driver. Either the
48k
LED or
44.1k
LED will illuminate to show which sample rate is in operation.
3
clock LEDs
There are two clock sources, internal or external, which are
configured via a PC using the FireWire driver. Either the
int
LED or
ext
LED
will illuminate to show the current clock source.
1
2
3
Содержание Venice F16
