Microlife BP A3L Comfort, Руководство пользователя

Страница: 6 / 87

4

When you select the 3 measurements, the MAM-symbol
BM
appears in the display.

The bottom, right hand section of the display shows a 1, 2 or 3 to
indicate which of the 3 measurements is currently being taken.

There is a break of 15 seconds between the measurements.
A count down indicates the remaining time.

The individual results are not displayed. Your blood pressure
will only be displayed after all 3 measurements are taken.

Do not remove the cuff between measurements.

If one of the individual measurements was questionable, a
fourth one is automatically taken.
3. Taking a Blood Pressure Measurement
Checklist for taking a reliable measurement
1. Avoid activity, eating or smoking immediately before the
measurement.
2. Sit down on a back-supported chair and relax for 5 minutes.
Keep the feet flat on the floor and do not cross your legs.
3. Always measure on the same arm (normally left). It is recom-
mended that doctors perform double arm measurements on a
patients first visit in order to determine which arm to measure in
the future. The arm with the higher blood pressure should be
measured.
4. Remove close-fitting garments from the upper arm. To avoid
constriction, shirt sleeves should not be rolled up - they do not
interfere with the cuff if they are laid flat.
5. Always ensure that the correct cuff size is used (marking on the
cuff).

Fit the cuff closely, but not too tight.

Make sure that the cuff is positioned 1-2 cm above the
elbow.
 The artery mark on the cuff (ca. 3 cm long bar) must lie over
the artery which runs down the inner side of the arm.

Support your arm so it is relaxed.

Ensure that the cuff is at the same height as your heart.
6. Press the ON/OFF button
1
to start the measurement.
7. The cuff will now pump up automatically. Relax, do not move
and do not tense your arm muscles until the measurement
result is displayed. Breathe normally and do not talk.
8. The measurement is performed during the inflation. The infla-
tion speed may vary, this is a normal occurence.
9. During the measurement, the pulse indicator
BK
flashes in the
display.
10.The result, comprising the systolic
AP
and the diastolic
AQ
blood pressure and the pulse rate
AR
is displayed. Note also the
explanations on further display symbols in this booklet.
11.When the device has finished measuring, remove the cuff.
12.Switch off the device. (The monitor does switch off automati-
cally after approx. 1 min.).
How not to store a reading
As soon as the reading is displayed press and hold the ON/OFF
button
1
until « M »
BP
is flashing. Confirm to delete the reading by
pressing the M-button
AK
.

You can stop the measurement at any time by pressing the
ON/OFF button (e.g. if you feel uneasy or an unpleasant
pressure sensation).
4. Appearance of the Irregular Heartbeat (IHB) Symbol
This symbol
BN
indicates that an irregular heartbeat was detected.
In this case, the measured blood pressure may deviate from your
actual blood pressure values. It is recommended to repeat the
measurement.
5. Traffic Light Indicator in the Display
The bars on the left-hand edge of the display
AS
show you the
range within which the indicated blood pressure value lies.
Depending on the height of the bar, the readout value is either
within the optimum (green), elevated (yellow), too high (orange) or
dangerously high (red) range. The classification corresponds to
the 4 ranges in the table as defined by the international guidelines
(ESH, ESC, JSH), as described in «Section 1.».
6. PC-Link Functions
This device can be used in conjunction with a personal computer
(PC) running the Microlife Blood Pressure A (BPA+) soft-
ware. The memory data can be transferred to the PC by
connecting the monitor via a cable.
Information for the doctor in case of repeated appearance of
the IHB symbol:
This device is an oscillometric blood pressure monitor that also
measures the pulse during blood pressure measurement and
indicates when the heart rate is irregular.