AMPLIFIER
SPEAKERS
INTERFACES
POWER
Output power:
80 Watt RMS
Power distribution:
40 Watt x 2
Harmonic distortion:
< 0.3% 1 W 1 kHz
Frequency response:
40 Hz - 20 kHz
Signal/Noise ratio:
> 80 dB
Separation:
> 50 dB
Tweeter driver type:
1" x 2
Tweeter rated power:
10 Watt x 2, 6 ohm
Bass driver type:
5.25" x 2
Bass rated power:
30 Watt, 4 ohm
Frequency range:
40 Hz - 20 kHz
Output:
Binding posts
Input:
2RCA sockets, 2.4 GHz wireless data
Wireless:
Infrared remote control
2.4GHz:
USB type A
Power supply:
AC 220 V - 240 V ~ 50 Hz, 600 mA or AC120V ~ 60Hz, 1.2 A
Operations
6
5
Frequently Asked Questions (FAQ) & Annex
- The end -
© 2010 Microlab Technology Co., Ltd
All rights reserved
All specifications and information are subject to changes without further notice
Battery compartment
Wireless remote control
Please observe battery
orientation when inserting
Battery installation
1. Locate the side tab of the remote control
2. Press the tab
3. Pull the top apart to expose the battery compartment
Note: Prolong un-use period, please remove batteries
to prevent leakage.
Specifications
If the problem still exists, please contact the distributor or seek professional advice.
Check if the audio source is working well
Check if the audio and speaker cables well connected
Check if the volume at right level
Static sound heard when
volume knob is turned
What are the products
supported?
Where to place this speaker
Check if the source file is not corrupted, play a different song and
test. Note that playing music file with above 192kbps bitrate is
recommended for better resolution.
heck if the satellite cable well connected, and ensure
source connection is correctly inserted
C
One or more satellite no sound
No Sound
Sound is distorted
Turn off the playback source first, then turn the speaker
volume knob several times. Playback again and monitor.
The static noise is due to dust, so simply turning the
volume will remove it easily.
It is magnetically shielded so can be placed near LCD TV
Monitor without any distortion
Any playback devices such as PC, notebook with USB slot, CD/DVD
player, Media Players with 2RCA or 3.5mm stereo plug.
Solutions
system will auto detect the device, “SYNIC wireless audio” and install its driver.
b.
Windows® operating system will then change the sound playback properties to the
“SYNIC wireless audio”. The blue LEDs will now blink slowly indicating both are paired
and on standby for data transfer.
c.
Please start your audio media software and start the playback.
d.
Next depress the side button of the USB dongle till the blue LED blinks quickly, then go
to the back of the main speaker and depress the rear pairing button till the blue LED
blinks quickly to activate the pairing sequence. Once paired, both LEDs will blink slowly
indicating successful connection.
f.
The LED will illuminate steadily
once music is played and music
data being transmitted.
e.
The pairing process is carried out
once only. Subsequent uses are
fully automatic except for re-
installation of operating system.
If the playback is not started, the
pairing will not work.
g.
If there is conflict with nearby
2.4GHz products, please repeat
the pairing process again.
Note: it is advisable not to turn the volume too loud or
to its extreme volume limit to avoid damage to
the speaker driver material and impair your hearing. Always adjust in slow increment.
2.4GHz LED status
Functions
Blink slowly
Blink quickly
Illuminate steady
Positive pairing or awaiting data transfer
Pairing in progress
Music data transfer
Not to scale
Remote control
Media player
Viewing screen
Stereo speaker arrangement
Ideal listening position and placement
VOL+
VOL-
RESET
INPUT
TREB+
BASS+
BASS-
TREB-
VOL-
VOL+
2.4GHz transmission
from 2.4GHz USB dongle
Notebook or
Desktop
80-H12W-97-0001-01 2010-08-11
