Microh LED BAR II Скачать руководство пользователя страница 3

Safety Instructions

This device has left the factory in perfect condition and to ensure safe operation, 
it is absolutely necessary for the user to follow the safety instructions and warning 

notes written in this user manual.

IMPORTANT!

Damages caused by the disregard of this user manual are not subject to 

warranty. The dealer will not accept liability for any resulting defects or problems.

If  this  device  has  been  exposed  to  temperature  changes,  do  not  switch  it  on 

immediately. The arising condensation could damage the device. Leave the device 

switched off until it has reached room temperature, and is dry.

This device falls under protection-class I, therefore it is essential that the device be 

grounded. The electrical connection must be carried out by a qualifi ed technician.

This device should only be used with rate voltage and frequency. Make sure that 

the available is not higher than 120V as stated at the end of this manual.

Make sure the power cord is never crimped or damaged in any way, as this could 

cause  shock  and  damage.  If  your  power  cord  is  damaged  in  any  way,  please 

purchase a new power cord from your local MICROH dealer. Always disconnect 

power, when the device is not in use or before cleaning it. Never pull out the plug 

by tugging the power cord.

During initial start-up, some smoke or smell may arise. This is a normal process, 

and does not necessarily mean that the device is defective. It should decrease 

gradually. Please do not project the beam onto combustible substances.

Fixtures cannot be installed on or near combustible substances. Keep more than 

50cm distance from wall or proper ventilation and air fl ow. If your fi xture is or has 

become damaged in any way, it shall be exclusively replaced or repaired by the 

manufacturer to avoid any hazard.

CAUTION!

Never touch the device during operation! The housing may heat up!

CAUTION!

Never look directly into the light source, 

as sensitive persons may suffer an epileptic shock.

CAUTION!

The electric connection must only be carried out by a qualifi ed electrician.

Содержание LED BAR II













Отзывы: