background image

NOTICE

Caution should be used when using a longer time constant. Initial frequency errors at 
the start of Disciplining produce phase errors that will grow proportionally with elapsed 
time. For slow (long Tau) Disciplining algorithms, the initial errors could grow outside 
the 

DisciplineThreshold

 or 

PhaseLimit

 settings before an adequate correction can 

be made by the algorithm, resulting in a JamSync and 

DisciplineLocked

 = 0. Gener-

ally, a good Discipline approach is to use a short Tau to make quick coarse corrections, 
then apply a longer Tau to further reduce the MAC’s phase and frequency error.

MAC-SA5X User’s Guide

DS50002938A-page 26

 2019 Microchip Technology Inc.

3.4.3

JamSync

When Disciplining is first enabled, the algorithm will implement a JamSync (Observable 
with the 

JamSyncing

 parameter). It will also occur whenever the 

Phase

 is beyond the 

PhaseLimit

 parameter. A JamSync has the benefit of speeding up the disciplining 

routine by quickly synchronizing the output 1PPS after one clock cycle (phase is briefly 
aligned, but frequency is not). The disciplining algorithm can then continue onward by 
further refining the frequency and phase errors. However, the drawback of a JamSync 
is that the user will observe a phase “jump” during the JamSync, rather than a slow 
steer as predicated by disciplining alone. To avoid said “jump”, the user can adjust the 

PhaseLimit

 parameter. This is particularly useful for long Disciplining time constants. 

However, the initial JamSync (when disciplining is initialized) cannot be avoided.

3.4.4

1PPS Phase Measurement Mode

Phase measurement mode does not steer or Discipline the MAC’s output frequency. 
Rather, it makes use of the MAC’s internal phase meter by reporting the time difference 
between the MAC’s internally-generated 1PPS output (pins J1-17,19) and the exter-
nally applied reference 1PPS active input (pins J1-5,7 or J1-1,3) once per second. 
Measurement resolution is approximately 450

 

ps. The mode is enabled with the 

PhaseMetering

 parameter and the internal phase difference can be read via the 

Phase

 parameter.

Note:

Tau has no effect on the 

Phase

 parameter.

3.4.5

Cable Length Compensation

The zero point of disciplining can be adjusted to accommodate cable and other instru-
mentation delays (or advances) that impact the arrival time of the 1PPS at the MAC 
1PPS input pin. The compensation value can be adjusted with the 

CableDelay

 

parameter.
The maximum compensation adjustment is ±0.5 seconds, where the positive sign indi-
cates phase advancement of the input 1PPS. For example, if there is 45

 

ns of delay 

(approximately 33 feet of RG-58 coaxial cable) between the on-time point and the MAC 
1PPS input then the compensation value would be +45.

Note:

Compensation is implemented in the disciplining algorithm, not in the phase 
measurement itself. The phase measurement, as reported through teleme-
try, reports the actual phase measurement. That is, if the MAC is disciplined 
with +50

 

ns of compensation, the phase meter reports –50

 

ns of phase dif-

ference when disciplining is settled.

Содержание SA5 Series
































































Отзывы: