manualshive.com logo in svg

Microchip Technology PIC12F1501, Руководство пользователя

Поделиться
Скачать
Microchip Technology PIC12F1501 Скачать руководство пользователя страница 257

PIC16(L)F1508/9

DS40001609E-page 258

 2011-2015 Microchip Technology Inc.

24.1

CLCx Setup

Programming the CLCx module is performed by config-
uring the four stages in the logic signal flow. The four
stages are:
• Data  selection
• Data gating
• Logic function selection
• Output polarity
Each stage is setup at run time by writing to the corre-
sponding CLCx Special Function Registers. This has
the added advantage of permitting logic reconfiguration
on-the-fly during program execution.

24.1.1

DATA SELECTION

There are 16 signals available as inputs to the configu-
rable logic. Four 8-input multiplexers are used to select
the inputs to pass on to the next stage. The 16 inputs to
the multiplexers are arranged in groups of four. Each
group is available to two of the four multiplexers, in

each case, paired with a different group. This arrange-
ment makes possible selection of up to two from a
group without precluding a selection from another
group.
Data selection is through four multiplexers as indicated
on the left side of 

Figure 24-2

. Data inputs in the figure

are identified by a generic numbered input name.

Table 24-1

 correlates the generic input name to the

actual signal for each CLC module. The columns labeled
lcxd1 through lcxd4 indicate the MUX output for the
selected data input. D1S through D4S are abbreviations
for the MUX select input codes: LCxD1S<2:0> through
LCxD4S<2:0>, respectively. Selecting a data input in a
column excludes all other inputs in that column.
Data inputs are selected with CLCxSEL0 and
CLCxSEL1 registers (

Register 24-3

 and 

Register 24-5

,

respectively).

Note:

Data selections are undefined at power-up.

TABLE 24-1:

CLCx DATA INPUT SELECTION

Data Input

lcxd1

D1S

lcxd2

D2S

lcxd3

D3S

lcxd4

D4S

CLC  1

CLC  2

CLC  3

CLC  4

LCx_in[0]

000

—

—

100

CLC1IN0

CLC2IN0

CLC3IN0

CLC4IN0

LCx_in[1]

001

—

—

101

CLC1IN1

CLC2IN1

CLC3IN1

CLC4IN1

LCx_in[2]

010

—

—

110

C1OUT_sync

C1OUT_sync

C1OUT_sync

C1OUT_sync

LCx_in[3]

011

—

—

111

C2OUT_sync

C2OUT_sync

C2OUT_sync

C2OUT_sync

LCx_in[4]

100

000

—

—

F

OSC

F

OSC

F

OSC

F

OSC

LCx_in[5]

101

001

—

—

T0_overflow

T0_overflow

T0_overflow

T0_overflow

LCx_in[6]

110

010

—

—

T1_overflow

T1_overflow

T1_overflow

T1_overflow

LCx_in[7]

111

011

—

—

T2_match

T2_match

T2_match

T2_match

LCx_in[8]

—

100

000

—

LC1_out

LC1_out

LC1_out

LC1_out

LCx_in[9]

—

101

001

—

LC2_out

LC2_out

LC2_out

LC2_out

LCx_in[10]

—

110

010

—

LC3_out

LC3_out

LC3_out

LC3_out

LCx_in[11]

—

111

011

—

LC4_out

LC4_out

LC4_out

LC4_out

LCx_in[12]

—

—

100

000

NCO1_out

LFINTOSC

TX_out 
(EUSART)

SCK_out (MSSP)

LCx_in[13]

—

—

101

001

HFINTOSC

FRC

LFINTOSC

SDO_out (MSSP)

LCx_in[14]

—

—

110

010

PWM3_out

PWM1_out

PWM2_out

PWM1_out

LCx_in[15]

—

—

111

011

PWM4_out

PWM2_out

PWM3_out

PWM4_out

Содержание PIC12F1501



















































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды