Microchip Technology Microsemi PolarFire Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 42

background image

Appendix: 1G Ethernet BASE-T and BASE-X Using Transceiver

Microsemi Proprietary DG0799 Demo Guide Revision 3.0

33

7

Appendix: 1G Ethernet BASE-T and BASE-X
Using Transceiver

The PolarFire FPGA family includes multiple embedded low-power, performance-optimized transceivers.
Each transceiver has both the physical medium attachment (PMA), protocol physical coding sub-layer
(PCS) logic, and interfaces to the FPGA fabric. The transceiver has a multi-lane architecture with each
lane natively supporting serial data transmission rates from 250 Mbps to 12.7 Gbps. For more
information, see

UG0677: PolarFire FPGA Transceiver User Guide

.

This section describes how 1G Ethernet BASE-T and BASE-X designs are implemented in PolarFire
FPGAs using the transceivers.

7.1

1G Ethernet BASE-T and BASE-X

page 33 shows the typical FPGA design for 1G Ethernet BASE-T.

Figure 37 •

1G BASE-T Design

page 33 shows the typical FPGA design for 1G Ethernet BASE-X.

Figure 38 •

1G BASE-X Design

1G Ethernet BASE-T

Link

Partner

XCVR

MAC

(CoreTSE/

CoreSGMII)

Mi-V

Soft

Processor

User Interface

Copper

PHY

FPGA Board

FPGA

Auto-negotiation

By PHY

Auto-negotiation By MAC

SGMII

TBI

MDIO Interface

1G Ethernet BASE-X

Link

Partner

XCVR

MAC

(CoreTSE/
CoreSMII)

Mi-V

Soft

Processor

User Interface

Optical SFP

Pluggable

Module

FPGA Board

FPGA

Auto-negotiation By MAC

TBI

SGMII

«
...
36
37
38
39
40
...
»

Содержание Microsemi PolarFire











































Отзывы:

Нет отзывов

Похожие инструкции для Microsemi PolarFire

Бренд: Yamaha Страницы: 20

Бренд: DFI Страницы: 39

Бренд: JETWAY Страницы: 46

BD7682FJ-LB-EVK-302

Бренд: Rohm Страницы: 5

Бренд: Advantech Страницы: 4

Бренд: Aaeon Страницы: 44

TB360-BTC PRO 2.0

Бренд: Biostar Страницы: 59

Бренд: Analog Devices Страницы: 6

Бренд: ITOX Страницы: 114

Бренд: MSI Страницы: 164

Бренд: ASROCK Страницы: 162

Z68A-G43 G3 Series

Бренд: MSI Страницы: 152

Бренд: ON Semiconductor Страницы: 2

Бренд: JETWAY Страницы: 42

Бренд: Toyama Страницы: 48

Бренд: DFI Страницы: 101

Бренд: DG Страницы: 16

Бренд: DFI Страницы: 69

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды