Microchip Technology ADM00668 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 52

Microchip Technology ADM00668 Скачать руководство пользователя страница 41

Software Description



2016 Microchip Technology Inc.

DS50002510A-page 41

4.3.5.2.3

Current Reading

This column displays the current being drawn from the attached device. If “End Value”
is selected (in the Demo Options section, Current Reading features), this will update
continuously. If “MAX Value” is selected, this will store the highest value of current
during the dwell time.

4.3.5.2.4

Dwell Time

“Dwell Time” column defines the amount of time a profile is applied (from PWR_EN set
to PWR_EN unset). Each profile can have a different dwell time value.

4.3.5.3

DEMO OPTIONS

4.3.5.4

CUSTOM FILE PATH QUICK LOAD

When starting the UCS1003-1 interface, the file paths are reset to a default path. If
desired, the user may save the files to an alternate location. This quick-load feature
saves the paths of the

Setup.txt

and all seven profile locations to quickly return or

change files with one click.

4.3.5.5

RUNNING THE DEMO

Once the files and settings are configured as desired, enable the Demo routine by
pressing the

Demo

switch within the Panel Controls area. The routine begins and the

results are displayed in Profile MAX and Current MAX fields. By default, the Demo
routine will enable the profile that is indicated by Profile MAX.
• Profile MAX: Stores the profile of the highest value of current draw.
• Current MAX: Stores the highest current associated with the Profile MAX #.

TABLE 4-3:

DEMO OPTIONS DESCRIPTION

Options

Description

Repeat if 0 mA

When this option is set, it will repeat if all of the profiles read 0 mA,
i.e. no device connected.

Repeat Forever

When set, it will repeat the set of files until unchecked.

Dead Batt. Repeat

When set, it will repeat the cycle with the specified Dead Batt.
Delay time. This is useful when the battery is completely
discharged and the device OS is unable to handshake with
UCS1003-1.

Dead Batt. Delay

This option is defined in minutes. Minimum is 0 minutes, maximum
is 10 minutes.

Current Reading

Displays either the End Value (last value before PWR_EN set low)
or MAX Value (highest value during Dwell Time)

Note:

The

Demo

tab does not need to be visible to activate the Demo routine.

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

«
...
39
40
41
42
43
...
»

Содержание ADM00668





















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды