manualshive.com logo in svg

MICRO-EPSILON thermoIMAGER TIM NetPCQ, Руководство по эксплуатации

Поделиться
Скачать
MICRO-EPSILON thermoIMAGER TIM NetPCQ Скачать руководство пользователя страница 23

Page 23

Operation

thermoIMAGER NetPCQ

Fig. 13 Local Area Connection 
Status 

Fig. 14 Local Area Connection 
Properties

Fig. 15 Internet Protocol Version 4 
(TCP/IPv4) Properties

  4. In the 

Local Area Connection

 

Properties

 window

, see Fig. 14, 

mark 

Internet Protocol Ver-

sion 4 (TCP/IPv4)

and go again to 

Properties

.

  5. Please open now in 

Internet Protocol Version 4 (TCP/IPv4) Properties

 

window

, see Fig. 

15, 

the register 

Alternate Configuration 

and activate the checkbox 

User configured.

 

6. Now enter a user-defined IP address for your PC. Note that the network portion of the address must be 
identical to the network portion of the IP address of the thermoIMAGER TIM NetPCQ, that is, it must be 
192.168.0. However, the IP address of the device portion must be different from the thermoIMAGER TIM 
NetPCQ address (IP address 192.168.0.100); for example, use IP address 192.168.0.1

, see Fig. 16.

Содержание thermoIMAGER TIM NetPCQ















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды