MICRO-DESIGN StarPin-C Скачать руководство пользователя страница 11

 

the batteries  much sooner than expected. Use this option carefully. If you have 
questions about this option, please contact LevelCon. 

 

Shock Delay 

This parameter helps in setting the time delay between consecutive shock detection. Please set 
the number of seconds after which the consecutive shock to the device should be detected. The 
default value of this parameter is 3600 

Digital Wake ( F100M device only) 

This feature is associated with digital input such as a high level float gauge for overfill protection 
or other types of normally open/normally closed contacts.

 If enabled,  the input device will close 

its circuit and engage the no/nc on the digital input of the F100m forcing the monitor to turn on 
and report. The Digital Wake value is set in seconds and correlates to the number of seconds 
that NO/NC waits after triggered to force the F100 to report, i.e. if set to 3 seconds, when the DI 
is triggered for more than 3 seconds, the unit will force a report.  The default value of this 
parameter is Off.  

GPS Timeout(s) 

This option enables device location reporting via GPS. This option should only be used for units 
that are deployed outdoors. Set the number of seconds the unit should wait before it obtains a 
GPS fix. The preferred value for this parameter is 60 seconds. A zero value means the unit will 
not attempt to obtain a GPS fix. By default the value of this parameter is zero. 
 

Warning : Location reporting via GPS is a battery intensive operation and should only 
be enabled if the unit is outdoors.  When installed, the StarPin’s solar panel must be 
oriented towards the sky to enable faster GPS fix and solar charging.  

Digital Output ( for F100M device only ) 

This is a normally open, normally closed feature. 
Off(Float) 
On(low) 

TCP Server 

This parameter is used to modify the endpoint at which data is to be sent to and is set to the 
LevelCon Cloud by default.  This parameter should not be modified without the assistance of a 
LevelCon representative. The default value for this parameter is f100.levelcon.com 
 

 

   

                    Micro-Design, Inc. | 

[email protected]

 | 972-488-8725 | 10525 Newkirk St. Suite 260 

 

Page 11 

 

Содержание StarPin-C























Отзывы: