Michel's Siderolling Tarp Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 12

Michel's Siderolling Tarp Скачать руководство пользователя страница 9

Michel’s Industries, Ltd.

Generic Siderolling Instructions

Rev: Feb 22/17

Michel’s

Industries, Ltd.,

PH: 306.366.2184 8

Step 8: Spring Lock Bracket Installation

(See Figure 15)

NOTE:

If it’s a silage end gate the spring lock brackets get mounted on the side of the box to allow the end gate to open

and close.

If ordered as an electric without backup crank skip to step 10.

Drill a 5/16" hole through the predrilled holes in the spring lock bracket and into the box. Secure the bracket with the

3/8"x1-1/4" self-threading bolts provided. Lock the tarp in the closed position, engaging the spring lock (E). Adjust the

angle of the spring lock so that the crank handles seats properly in the spring lock. Make sure that the spring lock

bracket does not interfere with the taillights.

Figure 12 Optional

Figure 13 Optional

Figure 14 Optional

Figure 15

OPTIONAL SILAGE GATE INSTALLATION

«
...
7
8
9
10
11
...
»

Содержание Siderolling Tarp













Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды