Miccus Home TX Pro, Руководство по эксплуатации, Страница: 6 / 6

Detailed Instruc Ɵ ons for Use
Power on/o ī
The Home TX Pro supports mini USB power. Connect one
end of the included USB power cable to the Home TX Pro USB jack;
connect the other end to a compa Ɵ ble USB power supply unit
(5V/500mA), computer, or television USB port. Any USB charger that
is rated at an output of 5V@500mA or higher is compa Ɵ ble and may
be used with the Home TX Pro.
Connec Ɵ ng Cables
The Home TX Pro ships with the following audio cables:
a) 3.5mm (mini-plug) male to RCA (red and white) male
b) Toslink digital op
Ɵ cal cable
c) RCA to RCA audio cable
•
The Home TX Pro requires an audio input source like a
computer, tablet, smartphone, television or stereo system, etc.
that can o ī er the Home TX Pro an audio signal/music to
transmit. The cable being used must be connected to the
appropriate input: either 3.5mm to the “Line In”, or toslink to
the “Op Ɵ cal In”. Use the included cable that is best for your
applica Ɵ on.
Note: The included USB cable with ferrite core is for USB power
only and does not offer an audio or data type connection. For
optimal performance, always use the provided USB cable with
your Home TX Pro. Since the Home TX Pro is a
long range transmitter it may be susceptible to RF interference;
the USB cable with ferrite core can help reduce poten Ɵ al
interference during opera Ɵ on.
5
Pairing
Note: The Home TX Pro and your Bluetooth® device should
be no more than one meter apart when pairing (the closer the be Ʃ er
un Ɵ l paired).
1. Power on your headphones, speaker or other compa Ɵ ble A2DP
Bluetooth® pro fi le device and engage pairing mode.
2. Place the Home TX Pro into pairing mode: press and
hold the power bu Ʃ on (8.5 seconds) un Ɵ l the Miccus® Home
TX Pro powers on and the indicator light goes from slow
fl ashing red to fast fl ashing red and blue.
3. When pairing is complete the Home TX Pro far LEFT indicator
will light a solid blue; single link pairing has been established.
4. Dual-link pairing allows for two Bluetooth® receiving devices to
pair with the Home TX Pro at a Ɵ me. Once you’ve
paired your fi rst set of headphones to the Home TX
Pro (steps 1-3 above), power down both the Home TX
Pro and your headphones. Repeat steps 1-3 to pair your second
set of headphones. Once the second set of headphones is
paired to the Home TX Pro, the far LEFT indicator will
turn solid blue. Turn on the fi rst pair of headphones and they
will automa Ɵ cally reconnect to the Home TX Pro. The
far RIGHT indicator will turn solid blue. When both pairing
indicators are lit solid blue, Dual-link pairing has been estab-
lished. With dual-link enabled the aptX Low Latency codec is
not func Ɵ onal.
Note: Leave the Home TX Pro con Ɵ nuously connected to
USB power, and powered on to automa Ɵ cally reconnect when the
last paired device is within range. If powered o ī or disconnected
from USB power, the Home TX Pro should automa Ɵ cally
reconnect with the last paired receiving device when both devices
are powered on and within range.
To begin streaming audio simply press the play bu Ʃ on on your audio
source and adjust volume to taste.
6
Home TX Pro User MW.indd Spread 6 of 6 - Pages(6, 7) Home TX Pro User MW.indd Spread 6 of 6 - Pages(6, 7) 12/21/16 12:02 PM 12/21/16 12:02 PM