MGL Avionics Vega INFO-1 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 33

background image

Vega INFO-1 Operating Manual

Page 27

7 Specifications

Operating Temperature Range

-20ºC to 50ºC (-4ºF to 122ºF)

Storage Temperature Range

-30ºC to 80ºC (-22ºF to 176ºF)

Power Supply

8 to 30Vdc SMPS (switch mode power supply) with built in 33V over
voltage and reverse voltage protection

Current Consumption

Approx. 73mA @ 13.8V (backlight highest setting), 33mA @13.8V
(backlight lowest setting)

Display

1.8” 160x128 pixel active matrix TFT display.
1000 cd/m2
Sunlight readable with anti-glare coating
LED Backlight is user configurable

Alarm Output

Open collector transistor switch to ground
Maximum rating 0.25A

ADC

12 bit

Dimensions

see Vega series dimensional drawing

Enclosure

2 1/4” (57mm) ABS, black in color, front or rear mounting. Flame retardant.

Weight

Approx. 120 grams (Instrument excluding cables)

Non-volatile memory storage

100000 write cycles

Voltage measurement range

Up to 32Vdc

Voltage resolution

0.1V

Current sensor supported

MGL Avionics Magnetic Closed Loop Current Sensor

G-force range

+-10g typical

OAT Temperature Sender type

Semiconductor LM335 (STMicroelectronics)

Internal battery type

CR2032

NMEA Supported Message

GPRMC (Recommended Minimum Sentence)
GPGGA (Global Positioning System Fix Data)
GPGSA (GPS DOP and active satellites)
GPGSV (GPS Satellites in view)

NMEA Supported Baud rate

1200 to 115200

8 Operating the alarms

The alarm output can be used to switch an external alarm indicator. The external alarm switch is an open collector
transistor switch to ground with a maximum rating of 0.25A DC. It is possible to wire the alarm contacts of several
Stratomaster instruments in parallel should this be desired. To avoid false activation of the alarms, the alarm function is
only active 10 seconds after the instrument has powered up.

9 Firmware Upgrading

The INFO-1 can be upgraded in the field by connecting the RS232 port to a PC and running the firmware update
program.

Note that only the RS232 port can be used to upgrade the firmware.

Please see the Vega firmware upgrading document for more information.

«
...
25
26
27
28
29
...
»

Содержание Vega INFO-1


































Отзывы:

Нет отзывов

Похожие инструкции для Vega INFO-1

Бренд: A&D Страницы: 100

Бренд: Anslut Страницы: 6

LaserLight 2 Series

Бренд: C&S Controls Страницы: 37

Бренд: VarTech Systems Страницы: 18

Бренд: Balmar Страницы: 19

Бренд: AOC Страницы: 26

Бренд: BenQ Страницы: 36

Бренд: ViewSonic Страницы: 69

Бренд: B&G Страницы: 88

Бренд: 2E Страницы: 32

Бренд: NEC Страницы: 64

Бренд: Shiseido Страницы: 17

Бренд: Haier Страницы: 28

42EP24S - 42" Plasma TV

Бренд: Haier Страницы: 50

Бренд: Haier Страницы: 15

42EP24S - 42" Plasma TV

Бренд: Haier Страницы: 33

Бренд: Kontron Embedded Computers Страницы: 39

Бренд: LG Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды