MG MERO 18 P Скачать руководство пользователя страница 3

 

  

 

  
  

 

 

OPERATING INSTRUCTIONS  

Pneumatic Carton Stapler for coiled staples 

MERO 18 P + MERO 22 P

 

 

Page:  

3

 

Mod.: 

804 

 

ET      675, 676 

 

Page 3 of  6                           04.05.2018 

 

3.2  Handling 

Insert staples into the magazine (7) (s. Chap. 3.3). Adjust the stapling tool as required  (s. Chap. 3.4 - 3.6). 
Place the stapler 

MERO 18 P or MERO 22 P 

on top of the carton to be sealed in a way that the flap joint 

is directly in the centre of the stapling tool (s. arrow in the front of stapler). Then activate trigger (8)  to 
release  stapling. The anvils will extend, clinch the staples and return automatically into the tool. Release 
trigger (8). Then move the tool to the next stapling position.  
For an optimal fastening result apply staples approx. 1cm to the rim of the carton. 
 

Caution: The stapler should only be moved with the anvils completely returned into the tool 
                to avoid damage to the retractable anvils! 

 

3.3 

To load staples

 

Before inserting staples disconnect air supply! 
The cover (7) has to be squeezed slightly and  folded backward. Insert the coil as shown into the magazine 
seat and push the staples into the stapling tool until stop. Then fold the cover (7) forward until the cover is 
locked. 
 

3.4   Adjusting leg length of staples 

Before adjusting disconnect air supply! 
Loosen screw with hexagonal recessed hole (I) with 3 mm hexagon spanner, turn the adjusting rod  (5) 
180° with a screw driver to the required position. For long leg length turn adjusting rod (5), so that L is in 
upright position, for short leg length turn adjusting rod (5), so that S is in upright  position. Fasten the 
screw again with hexagonal recessed hole (I). 
 
 

 
 

 

 

 

Staple coil 

MERO 18 P 

Leg length 

15 mm 
R 1/58 

18 mm 
R 1/34 

MERO 22 P 

Leg length 

18 mm 
R 1/34 

22 mm 
R 1/78 

adjusting 
rod -
position 

 

S

L

 

 

S

L

 

Содержание MERO 18 P












Отзывы: