MFJ MFJ-422E Скачать руководство пользователя страница 4

MFJ-422E/422EX Instruction Manual 

Electronic Keyer Paddle 

 

Paddle Installation for the MFJ-422EX 

 
If you purchased the MFJ-422EX (keyer without paddle), you must install it 
onto your paddle.  Follow these instructions for installing the MFJ-422EX onto 
a MFJ-564 or Bencher type paddle: 
 
1.

 

Remove any cables from the paddle.  Do not apply power to unit while it is 
disassembled. 
 

2.  Set up your MFJ-422EX now, using the nine internal jumpers, to the type 

of output keying required, the desired Iambic mode, the speed range, and 
the format of the serial number.  Refer to the “Jumper Settings” section on 
page 7 for the meanings of these jumpers. 

 
3.  If you wish to use a nine volt battery, install one now.  A nine volt battery 

fits in the battery clip located inside the case.  MFJ suggests the use of a 
good long-life alkaline battery for longest operation. 

 
4.  Remove the rubber foot from the bottom rear of the paddle. 
 
5.  Remove the plastic cable clamp from the bottom center of the paddle. 
 
6.  Slide the MFJ-422EX on to the back of the paddle.  Thread the cable 

through the slot on the bottom of the MFJ-422EX.  Secure the case with the 
rubber foot and new screws.  The MFJ-564 Iambic Paddle has four 
additional holes to better secure the case of the paddle. 

 
7.  Connect the BARE wire of the cable to the middle terminal on the bottom 

of the paddle for GROUND. 

 
8.  If you normally operate the paddle 

right-handed

, then connect the DOT 

(white or clear colored) wire to the 

left

 paddle terminal and the DASH 

(black) wire to the 

right

 terminal.  Connect the wires the opposite way if 

you operate the paddle 

left-handed

 
9.  Place the cable in the plastic cable clamp and secure it with a screw.  Fold 

any excess cable up into the unit. 

 
 

 
 

Содержание MFJ-422E

















Отзывы: