background image

Introduction

Thank you for purchasing the MFJ-1835H five band HF antenna.   You new antenna is composed of 
High strength material for excellent rigidly and light weight.  The MFJ-1835H is compact and excellent
for restricted space or portable installations.  The antenna is omnidirectional enough to not require a 
rotator.  It has good bandwidth and minimum SWR on all five bands.  It can be mounted on tripod for 
temporary locations or any mast 1-1/2 diameter or smaller for permanent installation. 

Preparation

This antenna although it is not heavy, might be cumbersome for one person to handle.  
It is a good idea to have a temporary mast about 6 feet off the ground to hold the antenna while you
are working on it.  If you don’t have a mast available, saw horses other support can be used.  
The antenna support arms can be installed on a flat surface like a garage floor if needed.  The antenna
assembly will go quickly and is fairly easy but take your time anyway.  As with all antennas, safety 
glasses are recommended during the assembly and tuning.  We don’t want you to “Poke your eye out”. 
Pick a clear open spot and assemble the antenna away from other people.  Do not allow children 
in the assembly area.  Only the people involved in the construction should be near.  If you plan to 
assemble the antenna over grass, be prepared to go on a lawn safari to find the hardware that you drop.
It’s not a question of if, but when you drop something.  A few extra parts have been included in the parts
pack for just such a adventure.   Assembly can be done by one person but when the antenna is to be 
mounted or moved, plan to have a friend help.  It is not wise to attempt to install any antenna without 
help.  Don’t rush.  The more time you put into the antenna, the happier you will be with  the results.  

WARNING

KEEP THIS ANTENNA  

AWAY FROM POWER LINES

Never mount or move any antenna where it can come into contact

with power lines.  If this antenna comes into contact with power 

lines, it can KILL you.  Never mount any antenna where if it fell

it could come into contact with power lines. 

Содержание MFJ-1835H












Отзывы: