MFJ Compact IntelliTuner MFJ-928 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 28

background image

MFJ-928 Compact IntelliTuner Automatic Antenna Tuner

Instruction Manual

©

2005 MFJ Enterprises, Inc.

3

Fast Start

WARNING

●

Never operate the tuner with its cover removed. Contact with the components inside the
tuner while transmitting will result in painful RF burns.

●

Locate the tuner so that the rear terminals are not accessible during operation. The single
wire connection may have high voltage while transmitting.

●

Disconnect all antennas from the tuner during lightning storms.

●

Always tune with low power (about 10 watts). Apply maximum power only after tuning up.

●

Never exceed tuner specifications.

●

Do not transmit with a high SWR for extended periods of time.

1.  Connect the MFJ-928 to a 12-15 VDC voltage source capable of supplying at least 750 milli-amps.
2.  Connect your transmitter to the TRANSMITTER connector using a 50-ohm coaxial cable.
3.  Connect your coax-fed antenna to the ANTENNA 1 connector using a 50-ohm coaxial cable, or

connect your random wire to the WIRE binding post.

4.  Connect your ground connection to the GROUND post.
5.  Press the [POWER] button to turn on the MFJ-928 tuner.
6.  Press the [ANT] button momentarily until there is one beep. One beep indicates that antenna 1 is

selected.

7. Key your transmitter to output a carrier of 10 watts CW, FM or AM.
8. Press and hold the [TUNE] button on the MFJ-928 for one second to start the automatic tuning

process. When completed, check to ensure an SWR of 2.0 or less before increasing RF power.

9. You are ready to transmit.

Note: During the automatic tuning process, the tuner will make some noise. These are the relays

switching at a very fast pace and it is normal operation. Do not be alarmed.

Note: When the tuner power is OFF, the tuner is in bypass mode and RF from the transmitter goes

directly to the antenna (ANTENNA 1) with no matching. When the tuner power is ON,
pressing [TUNE] quickly places the tuner in bypass mode (zero inductance and zero
capacitance) and indicates by one beep.

Transmitter

MFJ-928

50-ohm Coax

Antenna 1

RF Ground

12 VDC

Antenna 2

Figure 1. Installation Block Diagram.

«
...
5
6
7
8
9
...
»

Содержание Compact IntelliTuner MFJ-928





























Отзывы:

Нет отзывов

Похожие инструкции для Compact IntelliTuner MFJ-928

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 4

Бренд: Yamaha Страницы: 4

Бренд: Yamaha Страницы: 8

Бренд: Yamaha Страницы: 8

Бренд: Yamaha Страницы: 12

Бренд: Yamaha Страницы: 14

Бренд: Yamaha Страницы: 15

Бренд: Yamaha Страницы: 11

Бренд: Yamaha Страницы: 16

Бренд: Yamaha Страницы: 12

Бренд: Yamaha Страницы: 12

Бренд: Yamaha Страницы: 12

Бренд: Yamaha Страницы: 20

Бренд: Yamaha Страницы: 20

Бренд: Yamaha Страницы: 22

Бренд: Yamaha Страницы: 22

Бренд: Yamaha Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды