background image

MFJ-948 Versa Tuner II

 

WARNING:  To avoid problems, a dipole antenna should be a full half-wave on the 

lowest band.  On 160 meters, an 80 or 40 meter antenna fed the normal 
way will be extremely reactive with only a few ohms of feedpoint 
resistance.  Trying to load an 80 meter (or higher frequency) antenna on 
160 meters can be a disaster for both your signal and the tuner.  The best 
way to operate 160 with an 80 or 40 meter antenna is to load either or 
both feedline wires (in parallel) as a longwire.  The antenna will act like a 
"T" antenna worked against the station ground. 

 

Technical Assistance 
 

If you have any problem with this unit first check the appropriate section of this manual. If 
the manual does not reference your problem or your problem is not solved by reading the 
manual, you may call 

MFJ Technical Service

 at 

601-323-0549

 or the 

MFJ Factory

 at 

601-

323-5869

.  You will be best helped if you have your unit, manual and all information on 

your station handy so you can answer any questions the technicians may ask. 
 
You can also send questions by mail to MFJ Enterprises, Inc., 300 Industrial Park Road, 
Starkville, MS 39759; by FAX to 601-323-6551; or by email to [email protected].  
Send a complete description of your problem, an explanation of exactly how you are using 
your unit, and a complete description of your station. 

 

Downloaded from www.g7syw.com

www.g7syw.com

Содержание MFJ-948











Отзывы: