Meyra 1.610 страница 13 Скачать руководство пользователя | Manualshive

Страница: 13 / 104

background image

13

SAFETY INFORMATION

☞

Wear suitable clothing during service-jobs as
well as gloves and protective glasses when re-
quired.

Danger of injuries caused by inappropriate work

clothes.

☞

Secure the product against unintentional roll-
ing motions, tilting over or falling down e. g.
from a mounting rack.

Damages due to a not secured wheelchair.

☞

Clean/disinfect the product before inspection.

☞

If necessary, observe the care instructions and
product specific inspection instructions in-
cluded in the corresponding operating manu-
al as well as the safety and general handling
instructions <

Electronic vehicles

>.

Damages due to neglected cleaning.

☞

Keep your workspace clean and only use clean
cloths.

Damages caused by shavings and dirt particles.

☞

Use only suitable tools.

☞

View chapter

Required tools and aids

Damages caused by the use of incorrect tools.

☞

Replace loose screwed connections with
thread safety with the respective nut or screw
and new thread safety.

☞

If new screws or nuts with thread safety not be
available, apply liquid thread safety compound
with medium hardness e. g. Loctite® 241 or
Euro Lock A24.20.

Damages caused by loose screwed connections.

Storage

Dismantled parts are to be placed resp. stored safe-
ly and protected as well as sorted by commission.

REQUIRED TOOLS AND AIDS

For adjustments and maintenance we recommend
the use of high quality tools.

☞

High quality tools can prevent for example
damages to the surface of the frame as well as
minor injuries to the hand.

The tools required most frequently are:

Socket wrench
Open-end or ring spanner
Hexagon socket spanner
Phillips screwdriver
Slot screw driver

«
...
11
12
13
14
15
...
»

Содержание 1.610









































































































Отзывы:

Нет отзывов

Похожие инструкции для 1.610

PROFESSIONAL REHAB Series

Бренд: Neatech Страницы: 220

Бренд: I-GO Страницы: 28

Basket and Rugby Wheelchair

Бренд: WOLTURNUS Страницы: 26

Бренд: Invacare Страницы: 144

Бренд: R Healthcare Страницы: 19

Бренд: Yamaha Страницы: 46

Бренд: R82 Страницы: 16

Бренд: B+B Страницы: 19

Бренд: Raz Страницы: 15

Zitzi Flipper Pro

Бренд: Anatomic SITT Страницы: 20

Бренд: Roma Medical Страницы: 20

Бренд: Lifeline Страницы: 3

Бренд: Power Plus Mobility Страницы: 20

Бренд: DELTA-SPORT Страницы: 22

Бренд: DALLAS SOFA COMPANY Страницы: 7

Coral 3002010000

Бренд: Handicare Страницы: 14

Бренд: Küschall Страницы: 20

Бренд: Karma Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды