background image

M o d e l   M 3 2 3 0  

19 | 

P a g e

 

 
 

 

 
 

CLEANING AND STORAGE 

 
Before storing this spreader for an extended period of time, perform the following: 
 

1.  Allow the spreader to completely clean out the last load. 

 

2.  Thoroughly hose off all manure from the outside of the spreader and the inside of the box, particularly getting 

the end gate mechanism clean. The water can be drained into your manure storage pit or if the gate is left 
closed, the water can be taken to the field and spread. 

 

3.  If pressure washing spreader, be careful not to wash directly on or too close to any bearing seals. The high 

pressure can destroy the seal and force water into the bearing causing it to rust and fail. Avoid pressure 
washing painted areas of the spreader too closely as the pressure can strip paint on scratched areas. 

 

4.  Manure is very acidic and should not be left on painted areas for a long period of time because it will lift paint 

from the metal. Unpainted metal will corrode causing holes to rust through metal guards or even fall off the 
machine. If this should happen, guards must be replaced immediately. 

 

5.  After cleaning, lube the spreader to exclude moisture from bearings and prevent condensation from forming 

during storage. 

 

6.  Inspect all elements and check for parts that need repair or replacement. Performing these tasks now will 

guarantee that the spreader is ready for use at the beginning of the next season. 

 

 

 

 

WARNING

 

NEVER INFLATE BEYOND RIM OR TIRE 

MANU

FACTURER’S APPROVED PSI RATING. 

WHILE INFLATING, STAY OUT OF THE 

TRAJECTORY & STAND CLEAR OF TIRE/WHEEL 

ASSEMBLY. A TIRE BLOW OUT OR RIM/WHEEL 

FAILURE CAN CAUSE SERIOUS INJURY OR 

DEATH.

 

 

 DANGER

 

IF THE LOCK RING SHOULD BLOW OFF, IT AND 

OTHER PARTS COULD FLY OFF WITH ENOUGH 

FORCE TO INJURE OR KILL A PERSON. NEVER 

STAND IN THE POTENTIAL BLOW OUT AREA 

AND KEEP OTHERS AWAY.

 

 

Содержание M3230 Tandem





















































Отзывы: