Metso NELES NDX 511 Series Скачать руководство пользователя страница 69

Страница: 69 / 88

GENER

INFO

SPECS

MOUNTING

T UP

OPER

ATION

AINTENANCE

DIMENSIONS

ORDER

LOGISTICS

NDX VALVE CONTROLLER

13.5.3

Diagnosis

This window provides tools for quickly checking the device

state and all diagnosis information and tools. This window

provides realtime information of the device, measured

performance data, historical data and possibility to run

selfdiagnostics in the form of offline tests. This window

also has event log, which shows a log of events and actions,

which has occurred earlier to the device.

13.5.3.1 Performance

See the explanation in Performance chapter under the

Online Parameterize.

Fig. 63

13.5.3.2 Online Valve Signature

Fig. 64

Online Valve Signature feature shows the friction of the

control valve under normal process conditions when ever

the valve is changing position.Online Valve Signature shows

the amount of pressure required to move the valve in rela

tion to the valve opening. The device data is continuously

updated. To view the data in the DTM, read the data from

the device. The graph shows opening and closing pressures.

When the data has been read from the device, DTM auto

matically saves the graph to the database.

Advanced diagnostics

Comparison of two selected online valve signatures based

on the time stamp is available in advanced diagnostics

version of NDX.

Select wanted days and read your selection.

Monitoring

Fig. 65

Monitoring view will automatically poll eight device vari

ables in approximately every 1.5 seconds. All parameters

are uploaded regardless the state of the checkboxes. With

the checkboxes under the monitoring graphs, user can

filter out unwanted information. All parameters are also

automatically logged to a log file. The log file location is

determined by Metso Device DTM Configuration utility,

which can be found from the Windows Start menu. The

default location for the log file is: C:\ProgramData\Metso\

NDX Device DTM\Data.

13.5.3.3 Event log

Fig. 66

NOTE

Some of the features are available only in

Advanced Diagnostics version of NDX.

NOTE

Monitoring will be interrupted while reading

trend data from the device.

13 DEVICE TYPE MANAGER (DTM)

OPER

ATION

Содержание NELES NDX 511 Series

























































































Результаты поиска

Содержание NELES NDX 511 Series

Отзывы:

Похожие инструкции для NELES NDX 511 Series

Бренды по названию

Популярные бренды

Metso NELES NDX 511 Series, Инструкция по установке, обслуживанию и эксплуатации

Результаты поиска

Содержание NELES NDX 511 Series

Отзывы:

Похожие инструкции для NELES NDX 511 Series

Бренды по названию

Популярные бренды