METRUM Amethyst Скачать руководство пользователя страница 4

 

 

All-Engineering BV 
https://metrumacoustics.com 
info@metrumacoustics.com  
 

IMPORTANT SAFETY INSTRUCTIONS 
1. 

Read Instructions. 

2. 

Keep these Instructions. 

3. 

Heed all Warnings. 

4. 

Follow all Instructions. 

5. 

Do not use this apparatus near water. 

6. 

Clean only with a dry cloth. 

7. 

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus 

(including amplifiers) that produce heat. 

8. 

Unplug this apparatus during lightning storms or when unused for long periods of time. 

9. 

Refer all servicing to qualified service personnel. Servicing is required when the apparatus 

has been damaged in any way, such as a power-supply cord or plug is damaged, liquid has 
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to 
rain or moisture, does not operate normally, or has been dropped. 

10. 

The AMETHYST DAC must be placed on a firm, level surface where it is not exposed to dripping 

or splashing. 

11. 

Before making connections to the DAC, ensure that the power is off and other components 

are in mute or stand-by mode. Make sure all cable terminations are of the highest quality, 
free from frayed ends, short circuits, or cold solder joints. 

12. 

THERE ARE NO USER SERVICEABLE PARTS INSIDE THE "AMETHYST" DAC. 

Please contact All Engineering if you have any questions not addressed in this guide. 

13

. All Engineering cannot be held accountable and/or responsible for any form of damage or health 

issues inflicted to you, other people, pets, companies and non-living objects, that are caused by any 
form of usage of the product which is not described in this manual. 

14.

By actually using this product and turning it on for the first time, you agree to these terms 

 

 

Содержание Amethyst










Отзывы: