manualshive.com logo in svg

Metrotech 810 DX, Инструкции по эксплуатации

Поделиться
Скачать
Metrotech 810 DX Скачать руководство пользователя страница 21

810DX 9/9/2008 REV D 

21

one utility.  The signal is broadcast in all directions and can couple to every nearby utility through 
electromagnetic induction. It is possible to reduce the broadcasting signal by pressing the power 
output level button to change the power level from high to medium or medium to low. 
The transmitter induction antenna will be “ON” when there is no plug in the output jack. 
Sometimes it is not possible to gain access to the pipe or cable to make a direct connection or to 
use the MetroClamp.  In these cases use the Transmitter’s internal antenna. Three power levels 
can be selected when the Transmitter is “ON”, it will broadcast the signal from the internal 
antenna. No ground connection is needed when a signal is induced onto the target utility.   
 

1 

Position the Transmitter - 

Remove any cable or clamp plug from the OUTPUT JACK.     

             Position the Transmitter across the buried utility as indicated on Figure 6-3.

 

 
 

 

 

 

Figure 6-3:  Transmitter Position for Inductive Tracing 

 

2 

Turn the Transmitter ON.   

 

4 

Tracing the utility - Refer to Section 6.2 

 

6.2  Receiver Operation -   

When tracing a utility, always be alert to surrounding conditions 

which could interfere with the accuracy of your locate. Adjacent utilities pull the signal away from 
the target utility and can be misleading in both position and depth of the utility. Periodically sweep 
to each side of the utility to check for the presence of other utilities. The Receiver Left/Right 
Guidance System will indicate a second centerline, or will behave erratically if there is signal 
interference.

  

 

6.2.1 Receiver Set-up 

 

1 

Turn the Receiver ”ON” - 

Turn Receiver ON with quick press of ON/OFF DEPTH 

button.

 

 

2 

Check Battery Charge - 

The amount of battery charge will appear in the battery symbol 

in the upper left corner of the Receiver LCD. Replace the batteries if the symbol does not 
have any bars. See Section 8.3 for battery replacement. 

 
3 

Sweep the area - 

Hold the Receiver at a comfortable angle and make a 360-degree 

sweep 8 to 10 feet (2.5 to 3 m) around the connection point. During this sweep, stop at 
each centerline, note the signal strength. To do this, make sure the signal strength is 
below ”999”. Position the Receiver over the centerline and press the ON/OFF DEPTH 
button.

 

 
 
 
4 

Check for air coupling (Inductive mode only) - 

When using the inductive method, 

Содержание 810 DX





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды