Metrolab TFM1186 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 59

Metrolab TFM1186 Скачать руководство пользователя страница 31

THM1176/TFM1186 Use

r’s Manual

v 2.0 r 1.0

– 02/20

Copyright © 2020 Metrolab Technology SA

www.metrolab.com

27

5-5 IEEE 488.2 COMMON COMMANDS

As any IEEE 488.2 compliant instrument, the THM1176 family supports the
following commands.

Command Name

Description

*CLS

Clear status

Clear all event registers and queues (not
enable registers) and error buffer

*ESE
<NRf>

Program event
enable

Program standard event enable register

*ESE?

Event enable query

Read standard event enable register

*ESR?

Event status query

Read standard event register and clear it

*IDN?

Identification query

Returns the following information:
manufacturer; model; serial number; and
version of electronics, probe and firmware.
Note that this query returns “Arbitrary
ASCII Response Data” (see IEEE488.2
standard) and cannot be followed by
another query in the same command
sequence.

*OPC

Set operation
complete

Set the operation complete bit in the
standard event register after all commands
have been executed

*OPC?

Operation complete
query

Returns an ASCII “1” after all commands
have been executed

*RST

Reset

Reset device to power-on configuration

*SRE
<NRf>

Program status
enable

Program status enable register
Important: you must also enable service
requests on the host. See Section 5-7 for
details.

*SRE?

Status enable query

Read status enable register

*STB?

Status byte query

Read status byte register

*TRG

Trigger

Generate bus trigger

*TST?

Self-test Query

Perform complete self-test, return 0 if
successful, 1 if not

*WAI

Wait-to-Continue

Wait until previous commands have
completed

5-6 SCPI COMMANDS

In the command definitions below, the following conventions are used:

[]

optional keywords or parameters

<>

value

«
...
29
30
31
32
33
...
»

Содержание TFM1186




























































Отзывы:

Нет отзывов