Metra Electronics 99-7400 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 8

Metra Electronics 99-7400 Скачать руководство пользователя страница 8

7

8

3

Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(2) Phillips screws from the bottom of the
dash trim bezel. Remove (2) Phillips screws
above the radio opening. Unclip the dash
trim bezel and disconnect the defroster and
rear wiper wiring. Remove (4) screws
securing the factory head unit and
disconnect the wiring.

1

NISSAN Maxima 1987-88

2

"E"

"E"

Slide

Mounting Tabs #18

into slots

"E"

on

Bracket Set #9.

The

Mounting Tabs, Bracket and Bracket slots can be identified by the
stamped letter on each component.

Skip to the Installation

Instructions for ALL VEHICLES on Page #14.

Using the scored lines as a guide, cut and
remove the

dashed

portions of

Faceplate

#1.

3

Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(2) Phillips screws above the radio opening.
Remove the ashtray and (1) screw in the
right corner of the ashtray housing. Remove
(1) screw below the cigarette lighter and
unclip the dash trim bezel. Remove (4)
screws securing the factory head unit and
disconnect the wiring.

1

NISSAN Maxima 1989-91

2

"D"

"D"

Using the scored lines as a guide, cut and
r e m o v e t h e

d a s h e d

p o r t i o n s o f

Faceplate #1.

Slide

Mounting Tabs #18

into slots

"D"

on

Brackets #9.

The

Mounting Tabs, Brackets and Bracket slots can be identified by the
stamped letter on each component.

Skip to the Installation

Instructions for ALL VEHICLES on Page #14.

«
...
6
7
8

Содержание 99-7400









Отзывы:

Нет отзывов