background image

10

INITIALIZING THE INTERFACE

FINAL ASSEMBLY

Attention!

 If the interface loses power for any reason, the following steps will need to be 

performed again.

1. 

Refer to step 2 of “Installing the interface”.

2. 

Press the push-to-start button to start the vehicle.

3. 

Program the kit:

a. 

Once the touchscreen display loads up, select the vehicle type; “Ford F-150”.

b. 

Wait until the radio comes on, and the touchscreen display shows “SWC Configured*”. This 
process may take up to 3 minutes.

Note:

 

If the touchscreen display does not load up, or the radio doesn’t come on within 3 

minutes, and/or the touchscreen display does not show “SWC Configured*”, turn the vehicle 

off and disconnect the 5838 harnesses from port “A” in the touchscreen display. Check all the 

connections, reconnect the harness into the touchscreen display, and then try again. 

* For models with steering wheel controls.

4. 

Test all functions of the installation for proper operation, before reassembling the dash.

1. 

Secure the completed assembly into the upper dash using the factory hardware removed in 
step 5 of dash disassembly.

2. 

Snap the 

radio trim panel

 with 

touchscreen display

 over the completed assembly, and then

reassemble the dash in reverse order of disassembly.

Содержание 99-5834CH















Отзывы: