background image

Operating Instructions 
Warranty 
METACAP Spray Gun D/A 
 

 

 

4-6 

 

Version/Edition July 2008 

Warranty 

The warranty period for the METACAP Spray Gun D/A is 24 months. This 
period will start from the date of purchase. 

It is not possible to make any warranty claims: 

— 

regarding wear parts like gaskets, silencers, nozzles, needles or similar 
parts. 

— 

if the user does not observe the instructions of this operating manual. 

— 

if the user modifies the METACAP Spray Gun D/A without prior 
authorization of the manufacturer. 

— 

if other than original spare parts are used. 

— 

if the user tries to eliminate warranty deficiencies on his own without 
prior written consent of the manufacturer. 

The manufacturer must be informed in writing about any warranty claims 
immediately after the occurrence of the deficiency. Then, the METACAP 
Spray Gun D/A will have to be sent to the manufacturer to check the 
warranty claim. 

We are of course available for any maintenance or repair work which might 
become necessary. 

METACAP reserve the right to carry out all modifications which might be 
required for an improved functioning of the METACAP Spray Gun D/A. 

 

Содержание D/A

































Отзывы: