Metabo WXLA 24-180 Quick, Оригинальное руководство пользователя

Страница: 19 / 140

ENGLISH
19
ENG
parting grinder discs must lie flat on the Autobal-
ancer support flange.
8.3 Securing/Releasing the "Quick"
clamping nut (depending on features)
Securing the "Quick"clamping nut (1):
Do not use the "Quick" clamping nut if the
accessory has a clamping shank thicker than
8mm! In this case, use the clamping nut (12) with
2-hole spanner (13).
Only use the "Quick" clamping nut when
undamaged and in perfect operating condi-
tion : the arrow must point to the notch on the
outer ring (see illustration on page 3).
- Lock the spindle (see chapter 8.1).
- Fit the "Quick"clamping nut (1) on the spindle (2).
See illustration on page 3.
- Tighten the "Quick"clamping nut by turning
clockwise by hand.
- Turn the grinding wheel firmly clockwise to
tighten the "Quick"clamping nut.
Releasing the "Quick" clamping nut (1) :
- Lock the spindle (see chapter 8.1).
- Turn the "Quick"clamping nut (1) anticlockwise
to unscrew.
8.4 Securing/Releasing the clamping nut
(depending on features)
Securing the clamping nut (12):
The 2 sides of the clamping nut are different. Screw
the clamping nut onto the spindle as follows:
See illustration D on page 3.
- A) For thin grinding wheels:
The edge of the clamping nut (12) faces upwards
so that the thin grinding wheel can be attached
securely.
B) For thick grinding wheels:
The edge of the clamping nut (12) faces down-
wards so that the clamping nut can be attached
securely to the spindle.
- Lock the spindle. Turn the clamping nut (12)
clockwise using the 2-hole spanner (13) to
secure.
Releasing the clamping nut:
- Lock the spindle (see chapter 8.1). Turn the
clamping nut (12) anticlockwise using the 2-hole
spanner (13) to unscrew.
9.1 Switching On and Off
Always guide the machine with both hands.
Switch on first, then guide the accessory
towards the workpiece.
The machine must not be allowed to draw in
additional dust and shavings. When switching
the machine on and off, keep it away from dust
deposits. After switching off the machine, only
place it down when the motor has come to a
standstill.
Avoid inadvertent starts: always switch the
tool off when the plug is removed from the
mains socket or if there has been a power cut.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
both hands at the intended handles, take a secure
stance and concentrate on the work.
See illustration A on page 3.
Torque activation
Switching on: Slide the lock (6) in the direction of
the arrow and press the trigger (7).
Switching off: Release the trigger (7).
Continuous operation (depending on features)
Switching on: Slide the lock (6) in the direction of
the arrow, press the trigger (7) and keep it pressed.
The machine is now switched on. Now slide the
lock (6) in the direction of the arrow once more to
lock the trigger (7) (continuous operation).
Switching off: Press the trigger (7) and release.
9.2 Working instructions
Grinding:
Press down the machine evenly on the surface and
move back and forth so that the surface of the
workpiece does not become too hot.
Roughing: position the machine at an angle of 30°
- 40° for the best working results.
Separating:
Always work against the run of the
disc (see illustration). Otherwise
there is the danger of the machine
kicking back from the cut out of
control. Guide the machine evenly at
a speed suitable for the material being processed.
Do not tilt, apply excessive force or sway from side
to side.
Wire brushing:
Press down the machine evenly.
9 Use
17027004_0510 gr WS WXLA Autobal.book Seite 19 Mittwoch, 12. Mai 2010 3:46 15