Metabo 00348000, Оригинальное руководство пользователя

Страница: 10 / 16

10
en ENGLISH
Original instructions
1. Declaration of Conformity
We, being solely responsible: Hereby declare that
these angle grinders, identified by type and serial
number *1), meet the requirements of all relevant
directives *2) and standards *3). Technical
documents for *4) - see page 3.
2. Specified Conditions of Use
The cordless angle grinders, when fitted with
original Metabo accessories, are suitable for
grinding, sanding, separating and wire brushing
metal, concrete, stone, tiles, wood, plastics and
similar materials without the use of water.
The user bears sole responsibility for any damage
caused by inappropriate use.
Generally accepted accident prevention
regulations and the enclosed safety information
must be observed.
3. General Safety Information
For your own protection and for the
protection of your power tool, pay
attention to all parts of the text that are
marked with this symbol!
WARNING – Read the operating
instructions to reduce the risk of injury.
WARNING Read all safety warnings and
instructions. Failure to follow all safety
warnings and instructions may result in electric
shock, fire and/or serious injury.
Keep all safety instructions and information
for future reference.
Always include these documents when passing on
your power tool.
4. Special Safety Instructions
4.1 General Safety Recommendations for
Grinding, Sanding, Wire Brushing or
Cut-Off Grinding:
a) This power tool is intended to function as a
grinder, sander, wire brush or cut-off tool.
Read all safety warnings, instructions,
illustrations and specifications provided with
this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious injury.
b) Operations such as polishing are not
recommended to be performed with this
power tool. Operations for which the power tool
was not designed may create a hazard and cause
personal injury.
c) Do not use accessories which are not
specifically designed and recommended by
the tool manufacturer. Even if an accessory can
be attached to your power tool, this does not
ensure safe operation.
d) The rated speed of the accessory must be
at least equal to the maximum speed marked
on the power tool. Accessories running faster
than their rated speed can break and fly apart.
e) The external diameter and thickness of your
accessory must be within the capacity rating
of your power tool. Incorrectly sized accessories
cannot be adequately guarded or controlled.
f) The threaded mounting of accessories must
match the grinder spindle thread. For
accessories mounted by flanges, the arbour
hole of the accessory must fit the locating
diameter of the flange. Accessories that do not
match the mounting hardware of the power tool will
run out of balance, vibrate excessively and may
result in a loss of control.
g) Do not use damaged accessories. Inspect
accessories such as grinding discs before
each use for chips and cracks and inspect
backing pads for cracks, tear or excess wear
and wire brushes for loose or cracked wires. If
a power tool or accessory is dropped, inspect
for damage or install an undamaged
accessory. After inspecting and installing the
accessory, position yourself and bystanders
away from the plane of the rotating accessory
and run the power tool at maximum no-load
speed for one minute. Damaged accessories will
normally break apart during this test time.
h) Wear personal protective equipment. Use a
face shield, safety goggles or safety goggles
depending on the application. If necessary,
wear a dust mask, hearing protectors, gloves
and a workshop apron capable of stopping
small abrasive or workpiece fragments. Eye
protection must be capable of stopping flying debris
generated by various operations. A dust mask or
respirator must be capable of filtering particles
generated by your operation. Prolonged exposure to
high intensity noise may cause hearing loss.
i) Keep bystanders a safe distance away from
the work area. Anyone entering the work area
must wear personal protective equipment.
Fragments of a workpiece or broken accessory
may fly off and result in injury beyond the
immediate area of operation.
j) When carrying out tasks that involve a risk
of the mounted tool contacting hidden wiring,
make sure you hold the device on the
insulated gripping surfaces only. Cutting
accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
k) Position the cord clear of the rotating
accessory. If you lose control, the cord may be cut
or snagged and your hand or arm may be pulled
into the rotating accessory.
I) Never lay the power tool down until the
accessory has come to a complete stop. The