Merlin Hobbies Knife Loop Yak 3D Скачать руководство пользователя | Manualshive

Страница: 11 / 13

background image

11

Connect the Control Horns

Carefully select the mounting area for each control horn.  The horn should be in line with the control rod
coming from the servo arm and also align with the hinge of the control surface.  Take care to slot straight
through the surface and slip the horns into the slot you just made.

Glue them in with Thin CA. Do not use accelerator.

Mount the Radio, ESC, and Battery

Use hook and loop material to hold your receiver and electronic speed control under the wing as shown
below.

«
...
9
10
11
12
13
»

Содержание Knife Loop Yak 3D














Отзывы:

Нет отзывов

Похожие инструкции для Knife Loop Yak 3D

Бренд: Jamara Страницы: 16

Бренд: 4-Max Models Страницы: 8

Бренд: 4-Max Страницы: 38

Бренд: Radio Flyer Страницы: 2

Бренд: Old School Model Works Страницы: 18

Бренд: PLAYTIVE JUNIOR Страницы: 20

Бренд: marklin Страницы: 20

STAR WARS 75102

Бренд: LEGO Страницы: 124

Бренд: KBT Страницы: 12

Zoom Avia B.534 IV. Series Weekend

Бренд: Eduard Страницы: 2

B-17F rear interior

Бренд: Eduard Страницы: 4

Бренд: H-KING Страницы: 11

Бренд: E sky Страницы: 140

MEGA BLOKS SKYLANDERS 95305

Бренд: Activision Страницы: 2

Бренд: ubisoft Страницы: 18

Бренд: LEGO Страницы: 179

Amazing Value Tub

Бренд: K'Nex Страницы: 28

Premier J1e 4-6-4 HudsonSteam Locomotive

Бренд: M.T.H. Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды