manualshive.com logo in svg

Meritor MTC-4208X Series, Руководство по обслуживанию, Страница: 2 / 120

Поделиться
Скачать
Meritor MTC-4208X Series Скачать руководство пользователя страница 2

Service Notes

About This Manual

This manual provides service and repair procedures for Meritor MTC-
4208X/XL/XP/XLEV/XLEC, MTC-4210X/XL/XP/XLEV/XLEC, and MTC-
4213X transfer cases.

Transfer Case Interchangeability

The MTC-4208XL/XLEV/XLEC and MTC-4210XL/XLEV/XLEC transfer 
case models are directly interchangeable with MTC-4208XL and MTC-
4210XL transfer case specifi cations.

Interface points for the oil cooler inlet and outlet lines (if equipped) on 
the XL, XLEV, and XLEC models are different from the X and XP, which 
affect the lengths of the oil cooler lines. The exterior geometry of the 
housing and location of lubrication lines also change, which potentially 
impacts clearances to surrounding components. In addition, GS models 
cannot be used in place of the X models in applications with “engage-
on-the-fl y” systems or mid-ship pumps.

The MTC-4208XP, MTC-4210XP, & MTC-4213X transfer case 
models are backward-compatible with MTC-4208GS, MTC-
4210GS, and MTC-4213GS transfer case speci

fi

 cations.

There are no changes to the oil cooler interface points with these 
models.

For more information on MTC-4208, MTC-4210, and MTC-4213GS 
Series transfer cases, refer to Maintenance Manual MM-0146 - 
Transfer Cases. To obtain this publication, visit Literature on Demand at 
meritor.com.

Before You Begin

1.  Read and understand all instructions and procedures before you 

begin to service components.

2.  Read and observe all Warning and Caution hazard alert messages 

in this publication. They provide information that can help prevent 
serious personal injury, damage to components, or both.

3.  Follow your company’s maintenance and service, installation, and 

diagnostics guidelines.

4.  Use special tools when required to help avoid serious personal 

injury and damage to components.

Hazard Alert Messages

 

DANGER

A DANGER INDICATES A PROCEDURE THAT YOU MUST 
FOLLOW EXACTLY OR IT WILL CAUSE DEATH OR SERIOUS 
INJURY.

 

WARNING

A WARNING ALERTS YOU TO AN INSTRUCTION OR PROCE-
DURE THAT YOU MUST FOLLOW EXACTLY TO AVOID SERI-
OUS PERSONAL INJURY AND DAMAGE TO COMPONENTS.

 

CAUTION

A CAUTION ALERTS YOU TO AN INSTRUCTION OR PRO-
CEDURE THAT YOU MUST FOLLOW EXACTLY TO AVOID 
DAMAGE TO COMPONENTS.

 

THIS SYMBOL ALERTS YOU TO TIGHTEN FASTENERS TO A 
SPECIFIED TORQUE VALUE.

How to Obtain Additional Maintenance, 
Service, and Product Information

Visit Literature on Demand at meritor.com to access and order addi-
tional information.

Contact the Meritor OnTrac™ Customer Call Center at 866-668-7221 
(United States and Canada); 001-800-889-1834 (Mexico); or email 
[email protected].

How to Obtain Tools and Supplies 
Specifi ed in This Manual

Contact Meritor’s Commercial Vehicle Aftermarket at 888-725-9355.

Information contained in this publication was in effect at the time the 
publication was approved for printing and is subject to change without 
notice or liability. Meritor Heavy Vehicle Systems, LLC, reserves the 
right to revise the information presented or to discontinue the produc-
tion of parts described at any time.

Содержание MTC-4208X Series

























































































































Отзывы:

Нет отзывов