manualshive.com logo in svg

Meritor MM-0861, Руководство по обслуживанию

Поделиться
Скачать
Meritor MM-0861 Скачать руководство пользователя страница 90

Copyright Meritor, Inc., 2022

MM-0861  /  Revised 06-22
Page 88

Printed in USA

9     Installation

Installation

Hazard Alert Messages

Read and observe all hazard alert messages in this publication. 

 WARNING

To prevent eye injury, always wear eye protection when performing 
vehicle maintenance or service.

Install the Transfer Case

 DANGER

Follow all safety guidelines and instructions provided by the lifting 
device manufacturer. Check that the lift capacity marked on the 
lifting device, straps and chains is correct for the weight being 
lifted. If they are not marked with the lift capacity, do not use 
them. Inspect lifting straps to ensure they are not damaged. 
NEVER subject lifting straps to shocks or drop-loading. Failure to 
follow these directives can result in death or serious personal 
injury and damage to components.

 DANGER

Support the transfer case with a lifting strap when transferring
the assembly from the repair stand to the vehicle. A transfer
case not supported correctly can fall. Serious personal injury and
damage to components can result. 

1.  Use a suitable lifting device to move the transfer case from the 

repair stand to a suitable hydraulic roller jack. If used, remove 
the temporary eye-bolts and mounting brackets from the 
transfer case housing.

2.  Move the transfer case into position under the vehicle with the 

hydraulic roller jack.

3.  Install the transfer case into the vehicle with the mounting 

bolts. Tighten the bolts to the torque specification supplied by 
the vehicle manufacturer.

4.  Connect the drivelines to the input and output yokes of 

the transfer case. Refer to the vehicle manufacturer’s 
recommended procedure.

5.  Connect any switch or speed sensor wiring. 

6.  Fill the transfer case with the correct quantity of specified 

lubricant. Refer to "Lubrication and Maintenance" on page 97.

Oil Cooler Line Connections

MTC-4213, or MTC-4208 and MTC-4210 with Oil Cooler

NOTE:

 There are different transfer case lubrication systems 

available. Determine the transfer case model before ordering cooler 
adaptation ports.

MTC-4213 or MTC-4208 and MTC-4210 Models with 
PTO

MTC-4208X/XP, MTC-4210X/XP, and MTC-4213X

4007120a

OUTLET TO

 

OIL COOLER

DRAIN

PLUG

FRONT

LOOP LINE USED 

FOR NON-OIL 

COOLER 

OPERATION 

ONLY

INLET FROM

OIL COOLER

FRONT

Figure 9.1 

1.  Disconnect the loop line on top of the transfer case connecting 

the pump exit and return ports on the transfer case.  
Figure 9.1 and Figure 9.2.

2.  Install the cooler inlet and outlet lines.

MTC-4208 and MTC-4210 with Rear-Mounted Pump

1.  Disconnect the tube between the pump outlet and orificed 

elbow fitting at the front idler bearing port.

2.  Install the cooler inlet line at the pump outlet. Connect the 

cooler outlet line to the front idler bearing orificed elbow. 
Figure 9.2, Figure 9.3, and Figure 9.4.

3.  Connect the oil exit line JIC fitting to the transfer case. Tighten 

to 20 lb-ft (27.2 Nm).

4.  Connect the oil return line JIC fitting to the transfer case. 

Tighten to 20 lb-ft (27.2 Nm). 

Содержание MM-0861























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды