Meritor MM-0861 Скачать руководство пользователя страница 80

Страница: 80 / 118

MM-0861 / Revised 06-22
Page 78

Printed in USA

7 Assembly

Transfer Case Assembly Test

CAUTION

The air pressure must not exceed 10 psi (0.69 bar). Damage to
components can result.

1. Pressure test the transfer case assembly for air leakage.

2. Verify the fittings are installed correctly.

3. Remove the breather assembly. Figure 7.51.

MTC-4208X AND MTC-4210X

REAR OUTPUT

POSITION

PTO

LOCATION

4004233a

BREATHER

REAR COVER

Figure 7.51

4. With the correct fitting installed into the breather port, apply a

pressure of 8-10 psi (0.55-0.69 bar).

5. Shut the air supply off.

If the pressure decreases by more than 2 psi (0.14 bar)
in 10 minutes:

Check for external leaks at the fittings.

6. Correct the leakage problem and retest.

7. Reinstall the breather assembly.

Содержание MM-0861























































































































Результаты поиска

Содержание MM-0861

Отзывы:

Бренды по названию

Популярные бренды

Meritor MM-0861, Руководство по обслуживанию

Результаты поиска

Содержание MM-0861

Отзывы:

Бренды по названию

Популярные бренды