manualshive.com logo in svg

Meritor MM-0861, Руководство по обслуживанию

Поделиться
Скачать
Meritor MM-0861 Скачать руководство пользователя страница 67

Copyright Meritor, Inc., 2022

MM-0861  /  Revised 06-22

Page 65

Printed in USA

7     Assembly

5.  Install the push rod into the transfer case.

6.  Install the front output shaft, shift fork, and clutch collar in the 

front case. The shift fork will slide over the push rod.  
Figure 7.16 and Figure 7.17.

4000204a

Figure 7.16 

4000205a

Figure 7.17 

7.  Install the release spring over the push rod and shift fork.

8.  Temporarily install the shift cylinder onto the case to secure 

the push rod in place.

9.  The shift cylinder requires Loctite

®

 272 sealant for final 

assembly.

10.  Install the input shaft, input bearing cage, and internal oil 

pump, if equipped. Refer to page 65 for the procedure.

11.  For MTC-4213X transfer cases, install the upper rear output 

shaft into the rear transfer case half. Refer to page 66 for 
the procedure.

12.  Install the pocket bearing into the recess in the input shaft. 

 

NOTE:

 All shaft bearing end plays must be determined before 

final assembly. Refer to "End Play Check and Adjustment" on 
page 67. 

13.  Install the two locating dowel pins into the corresponding 

holes in the front case. 
 

NOTE:

 Do not install sealant at this time.

 DANGER

Follow all safety guidelines and instructions provided by the lifting 
device manufacturer. Check that the lift capacity marked on the 
lifting device, straps and chains is correct for the weight being 
lifted. If they are not marked with the lift capacity, do not use 
them. Inspect lifting straps to ensure they are not damaged. 
NEVER subject lifting straps to shocks or drop-loading. Failure to 
follow these directives can result in death or serious personal 
injury and damage to components.

14.  Use a suitable lifting device to install the rear cover and output 

shaft as an assembly over the front case. Figure 7.18. Guide 
the cover over the shift fork and push rod as the cover is 
being set into place over the case.

4000207a

Figure 7.18 

15.  Verify the locating dowel pins have engaged both the case 

and the cover and that the cover is fully seated on the case.

16.  Secure the case to the cover joint by assembling at least six 

equally spaced case-to-cover capscrews.

Install the Front Input Shaft, Input 
Bearing Cage, and Internal Oil Pump 
Assembly Installation (If Equipped)

1.  Rotate the transfer case so the front is facing UPWARD.

Содержание MM-0861























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды