background image

1 - W

ARRANTY

 I

NFORMATION

90-8M0098854   MARCH  2015

9

1
2
3
4
5
6
7
8
9

M

ANUFACTURER

'

S

 W

ARRANTY

 C

OVERAGE

Select electronic emission‑related control parts from model year

2009 and later sterndrive engines are warranted for three years or

480 hours, whichever first occurs. Select mechanical

emission‑related components are warranted for one year or 150

hours of operation, whichever first occurs for engines greater than

500 horsepower and less than or equal to 650 horsepower and for 1

year or 50 hours, whichever first occurs for engines greater than 650

horsepower. However, warranty coverage based on the hourly

period is only permitted for engines that are equipped with hour

meters as defined in s 2441(a)(13) or their equivalent. If any

emission‑related part on your engine is defective under warranty,

the part will be repaired or replaced by Mercury Racing.

O

WNER

'

S

 W

ARRANTY

 R

ESPONSIBILITIES

As the sterndrive engine owner, you are responsible for the

performance of the required maintenance listed in your owner's

manual. Mercury Racing recommends that you retain all receipts

covering maintenance on your sterndrive engine, but Mercury

Racing cannot deny warranty solely for the lack of receipts or your

failure to ensure the performance of all scheduled maintenance.
As the sterndrive engine owner, you should however be aware that

Mercury Racing may deny you warranty coverage if your sterndrive

engine or a part has failed due to abuse, neglect, improper

maintenance, or unapproved modifications.
You are responsible for presenting your sterndrive engine to a

Mercury Marine distribution center as soon as a problem exists. The

warranty repairs will be completed in a reasonable amount of time,

not to exceed 30 days. If you have any questions regarding your

warranty rights and responsibilities, you should contact Mercury

Racing at 1‑920‑924‑2088.

E.P.A. E

MISSION

 C

ONTROLS

I

NTRODUCTION

Consistent with the obligations created by 40 CFR Part 1045,

Subpart B, Mercury Marine provides an emission warranty of three

years or 480 hours of engine use, whichever occurs first, to the retail

purchaser for electrical components of the emission control system,

and one year or 150 hours of engine use, whichever occurs first, to

the retail purchaser for mechanical components of the emission

control system. The engine is designed, built, and equipped to

conform at the time of sale with applicable regulations under section

213 of the Clean Air Act, and the engine is free from defects in

materials and workmanship that cause the engine to fail to conform

with applicable regulations.

E

MISSION

 C

ONTROL

 S

YSTEM

 C

OMPONENTS

The emission‑related warranty covers all components whose failure

would increase an engine's emission of any regulated component

including the following list of components:

1. Fuel metering system

a. Carburetor and internal parts (or fuel pressure regulator or

fuel injection system)

b. Air/fuel ratio feedback and control system
c. Cold start enrichment system
d. Intake valves

2. Air induction system

a. Controlled hot air intake system
b. Intake manifold
c. Air filter
d. Turbocharger systems

Содержание Racing 1100 STERNDRIVE













































































Отзывы: