Mercury MerCruiser MCM 4.3L BRAVO Скачать руководство пользователя | Manualshive

Страница: 26 / 40

background image

MAINTENANCE

SERVICE MANUAL NUMBER 25

Page 1B-26

90-861328--1 NOVEMBER 1999

Inspection

1. Inspect drive belt for the following:

•

Excessive wear

•

Cracks

NOTE: Minor, transverse cracks (across the belt width) may be acceptable. Longitudinal
cracks (in direction of belt length) that join transverse cracks are NOT acceptable.

•

Fraying

•

Glazed surfaces

75130

b

a

a -

Fraying

b -

Cracks

Replacing and/or Adjusting Tension

REMOVAL

1. Loosen 5/8 in. locking nut on adjustment stud.

2. Turn adjustment stud and loosen belt.

3. Remove drive belt.

INSTALLATION AND ADJUSTMENT

4. Install drive belt on pulleys.

5. Adjust tension by loosening 5/8 in. locking nut on adjustment stud. Leave wrench on

adjustment stud.

NOTE: Belt deflection is to be measured on the belt at the location that has the longest dis-
tance between two (2) pulleys. Proper tension is 1/4 in. (6 mm) deflection with moderate
thumb pressure.

6. Use 5/16 in. socket and tighten adjusting stud until the correct deflection of the belt is

obtained at location specified above.

«
...
24
25
26
27
28
...
»

Содержание MerCruiser MCM 4.3L BRAVO









































Отзывы:

Нет отзывов

Похожие инструкции для MerCruiser MCM 4.3L BRAVO

Бренд: Stihl Страницы: 40

Бренд: E-MAG Страницы: 30

Бренд: Nissei Страницы: 16

Vickers M2-200 Series

Бренд: Eaton Страницы: 16

Бренд: Deutz Страницы: 37

Бренд: ABB Страницы: 13

Бренд: Sesame Motor Страницы: 4

Бренд: Willys Страницы: 77

Бренд: Kubota Страницы: 47

Бренд: Kubota Страницы: 181

Бренд: BGS technic Страницы: 8

Бренд: TCF Страницы: 16

Бренд: Volvo Страницы: 8

Бренд: TOHATSU Страницы: 87

Бренд: DANA Страницы: 3

Бренд: O.S. engine Страницы: 48

Бренд: Honda Страницы: 48

Бренд: LONCIN Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды