Mercury MerCruiser Axius SeaCore 350 MAG Скачать руководство пользователя

Страница: 37 / 170

Section 2 - Getting to Know Your Power Package

90-8M0050539

eng

MAY 2011

Page 29

Panel Mount Features

a -

Neutral lock button

b -

Throttle only button

c -

Lanyard stop switch

d -

Control handle tension adjustment screw

e -

Control handle

f -

Trim/tilt button

Neutral Lock Button -

Prevents accidental shift and throttle engagement. Neutral lock button must be pushed into move the

control handle out of neutral.

Throttle Only Button -

Allows engine throttle advancement without shifting the engine. This is done by disengaging the shift

mechanism from the control handle. The throttle only button can be depressed only when the remote control handle is in the

neutral position, and should only be used to assist in starting the engine.

Lanyard Stop Switch -

Turns the ignition off whenever the operator (when attached to the lanyard) moves far enough away from

the operator's position to activate the switch. Refer to

Lanyard Stop Switch

for information on the use of this switch.

Control Handle -

Operation of the shift and throttle are controlled by the movement of the control handle. Push the control handle

forward from neutral with a quick firm motion to the first detent for forward gear. Continue pushing forward to increase speed. Pull

the control handle back from neutral with a quick firm motion to the first detent for reverse gear and continue pushing back to

increase speed.

Control Handle Tension Adjustment Screw - (not visible)

This screw is used to adjust the effort required to move the remote

control handle. Refer to instructions provided with remote control for complete adjustment instructions.

Trim/Tilt Button -

Refer to

Power Trim

Console Mount Features

a -

Throttle Only Button

b -

Control Handle

c -

Power Trim Switch

d -

Trailer Switch

Throttle Only Button -

Allows engine throttle advancement without shifting the engine. This is done by disengaging the shift

mechanism from the control handle. The throttle only button can be depressed only when the remote control handle is in the

neutral position.

mc77019-1

mc79503-1

Содержание MerCruiser Axius SeaCore 350 MAG











































































































































































Результаты поиска

Содержание MerCruiser Axius SeaCore 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius SeaCore 350 MAG

Бренды по названию

Популярные бренды

Mercury MerCruiser Axius SeaCore 350 MAG, Руководство пользователя

Результаты поиска

Содержание MerCruiser Axius SeaCore 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius SeaCore 350 MAG

Бренды по названию

Популярные бренды