Mercury MerCruiser Axius SeaCore 350 MAG Скачать руководство пользователя

Страница: 159 / 170

Section 7 - Troubleshooting

90-8M0050539

eng

MAY 2011

Page 151

Engine Runs Rough, Misses, or Backfires

Possible Cause

Remedy

Clogged fuel filter.

Replace filter.

Stale or contaminated fuel.

If contaminated, drain tank. Fill with fresh fuel.

Kinked or clogged fuel line or fuel tank vent line. Replace kinked lines or blow out lines with compressed air to remove

obstruction.

Flame Arrestor dirty.

Clean Flame Arrestor.

Faulty ignition system component.

Service ignition system.

Idle speed too low.

Have EFI system checked by an authorized Mercury MerCruiser dealer.

EFI System fault.

Have EFI System checked by an authorized Mercury MerCruiser dealer.

Poor Performance

Possible Cause

Remedy

Throttle not fully open.

Inspect the throttle cable and linkages for proper operation.

Damaged or improper propeller.

Replace the propeller.

Excessive bilge water.

Drain and check for cause of entry.

Boat overloaded or load improperly distributed.

Reduce load or redistribute load more evenly.

Flame arrestor dirty.

Clean the flame arrestor.

Boat bottom fouled or damaged.

Clean or repair as necessary.

Ignition problem.

See

Engine Runs Rough, Misses or Backfires

Engine overheating.

See

Excessive Engine Temperature

EFI System fault

Have EFI System checked by an authorized Mercury MerCruiser dealer.

Excessive Engine Temperature

Possible Cause

Remedy

Water inlet or seacock closed.

Open.

Drive belt loose or in poor condition.

Replace or adjust belt.

Seawater pickups or sea strainer obstructed.

Remove obstruction.

Faulty thermostat.

Replace.

Coolant level (if equipped) low in closed cooling section.

Check for cause of low coolant level and repair. Fill system with

proper coolant solution.

Heat Exchanger or Fluid Cooler plugged with foreign material Clean Heat Exchanger, Engine Oil Cooler, and Transmission

Oil Cooler (if equipped).

Loss of pressure in closed cooling section.

Check for leaks. Clean, inspect and test pressure cap.

Faulty seawater pickup pump.

Repair.

Seawater discharge restricted or plugged.

Clean exhaust elbows.

Insufficient Engine Temperature

Possible Cause

Remedy

Faulty thermostat.

Replace.

Содержание MerCruiser Axius SeaCore 350 MAG











































































































































































Результаты поиска

Содержание MerCruiser Axius SeaCore 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius SeaCore 350 MAG

Бренды по названию

Популярные бренды

Mercury MerCruiser Axius SeaCore 350 MAG, Руководство пользователя

Результаты поиска

Содержание MerCruiser Axius SeaCore 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius SeaCore 350 MAG

Бренды по названию

Популярные бренды