Mercury MerCruiser Axius SeaCore 350 MAG Скачать руководство пользователя

Страница: 122 / 170

Section 5 - Maintenance

Page 114

90-8M0050539

eng

MAY 2011

Sterndrive Surface Care

Standard Bravo sterndrive

a -

Sacrificial trim cylinder anode

b -

Sacrificial anodic plate

c -

Steering lever ground wire

d -

Ground wire between the gimbal ring and bell housing

e -

Stainless steel hoses

f -

Ground wire between the gimbal housing and trim cylinder

g -

Ground wire between the gimbal ring and gimbal housing

We recommend the following maintenance items to help keep your sterndrive corrosion‑free:
•

Maintain a complete paint covering on the sterndrive.

•

Check the finish regularly. Prime and paint nicks and scratches using Mercury enamel paint and touch up paint. Use only tin–

based anti–fouling paint or its equivalent on or near aluminum surfaces below the waterline.

•

If bare metal is showing, apply 2 coats paint.

Description

Where used

Part number

Mercury Phantom Black

Bare metal

92‑ 802878‑1

•

Spray all electrical connections with sealant.

Tube Ref No.

Description

Where Used

Part No.

Liquid Neoprene

All electrical connections

92- 25711 3

•

Inspect the sacrificial trim tab or anode plate if equipped, at regular intervals and replace it before it is half gone. If a stainless

steel propeller is installed, additional anodes or a MerCathode System will be required.

•

Inspect the propeller shaft for fishing line, which can cause corrosion on a stainless steel shaft.

•

Remove the propeller at least every 60 days and lubricate the propeller shaft.

•

Do not use lubricants containing graphite on or near the aluminum in saltwater.

•

Do not paint trim tabs or the mounting surface.

Flushing the Power Package—Alpha

Your boat comes equipped with through the sterndrive water pickups. See

Sterndrive Water Pickups

(following) for the flushing

procedure. Consult your authorized Mercury MerCruiser dealer for further explanation.
IMPORTANT: Alpha engines with the sterndrive water inlet blocked off at the gimbal housing, and using a through the hull water

inlet, need a supply of cooling water available to both the sterndrive and to the engine during operation

21083

Содержание MerCruiser Axius SeaCore 350 MAG











































































































































































Результаты поиска

Содержание MerCruiser Axius SeaCore 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius SeaCore 350 MAG

Бренды по названию

Популярные бренды

Mercury MerCruiser Axius SeaCore 350 MAG, Руководство пользователя

Результаты поиска

Содержание MerCruiser Axius SeaCore 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius SeaCore 350 MAG

Бренды по названию

Популярные бренды