manualshive.com logo in svg

Mercury MerCruiser Alpha 5.7L, Инструкция по эксплуатации, Страница: 46 / 48

Поделиться
Скачать
Mercury MerCruiser Alpha 5.7L Скачать руководство пользователя страница 46

(–)

(+)

76064

BLK = BLACK

BLU = BLUE

BRN = BROWN

GRY = GRAY

GRN = GREEN
ORN = ORANGE

PNK = PINK

PUR = PURPLE
RED = RED

TAN = TAN

WHT = WHITE

YEL = YELLOW

LIT = LIGHT

DRK = DARK

1

3

4

5

6

7

8

9

10

11

12

13

14

15

17

2

16

18

19

20

21

GASOLINE ENGINES SKI MODELS

Page 46 of 48

MIE 350 Magnum MPI, Black Scorpion and MX 6.2L MPI Engines -
Fuel and Ignition System Harness

NOTE: All BLACK wires with a ground symbol are interconnected within the EFI system har-
ness.

NOTE: Component position and orientation shown is arranged for visual clarity and ease
of circuit identification.

1 - Fuel Pump
2 - Distributor
3 - Coil
4 - Knock Sensor (KS) Module
5 - Data Link Connector (DLC)
6 - Manifold Absolute Pressure (MAP) Sensor
7 - Idle Air Control (IAC)
8 - Throttle Position (TP) Sensor
9 - Engine Coolant Temperature (ECT) Sensor
10- Electronic Control Module (ECM)
11- Fuel Pump Relay

12- Ignition/System Relay
13- Fuse (15 Amp) Fuel Pump, Fuse (15 Amp) ECM/DLC/Bat-

tery,Fuse (10 Amp) ECM/Injector/Ignition/Knock Module

14- Harness Connector To Starting/Charging Harness
15- Positive (+) Power Wire To Engine Circuit Breaker
16- Shift Plate (Not used on Ski models)
17- Oil Pressure (Audio Warning System)
18- Gear Lube Bottle (Not used on Ski models)
19- Fuel Pressure Switch
20- Water Temperature Sender

Содержание MerCruiser Alpha 5.7L

















































Отзывы:

Нет отзывов