Mercury 92-858058K01 страница 135 Скачать руководство пользователя

Страница: 135 / 150

Section 7 - Troubleshooting

90-879172181

eng

FEBRUARY 2011

Page 127

Fault Code

Fault Code (continued)

•

Battery Voltage High

•

Battery Voltage Low

•

Check Engine

•

Compass Sensor Fault

•

Compass Sensor Fault

•

Configuration Fault

•

Drive Gear Lube Low

•

Drive Hydraulic Oil Level Low

•

Drive Hydraulic Oil Temp High

•

Drive Position Sensor Fault

•

Drive Pressure Control Fault

•

Drive Pressure Sensor Fault

•

Drive Setup Incomplete

•

Drive Steering Control Fault

•

Drive Steering Response Fault

•

Drive Tab Control Fault

•

Drive Tab Position Sensor

•

Drive Tab Response Fault

•

Drive Temp Sensor Fault

•

Engine Coolant Level Low

•

Engine Coolant Temp High

•

Engine Limited/Drive Disabled

•

Engine Limited/Drive Warning

•

Engine Limited/Lever Fault

•

Engine Oil Pressure Low

•

Engine Oil Temperature High

•

Engine Start Unsuccessful

•

Exhaust Temperature High

•

Exhaust Temperature Sensor

•

Exhaust Temperature Severe

•

Fuel Pressure Low

•

Global Position Sensor Fault

•

Global Position Sensor Fault

•

Global Position Sensor No Fix

•

Global Position Sensor NoFix

•

Helm Joystick Disabled

•

Helm Joystick Fault

•

Intake Manifold Pressure High

•

Intake Manifold Temp High

•

Joystick Operation Disabled

•

Joystick Operation Minimal

•

Joystick Operation Reduced

•

Joystick Station Configuration Fault

•

Joystick Station Fault

•

Joystick Station Faulted

•

Joystick Station Lost

•

Joystick Station Setup Fault

•

Lever Overriding Joystick

•

LeverMasterFault

•

Precision Pilot Control Fault

•

Precision Pilot ControlFault

•

Service Steering Filter

•

Single Lever Mode Unavailable

•

Starter System Fault

•

Steering Wheel Fault

•

System Communication Fault

•

System Communication Fault

•

System Communication Fault

•

System Communication Fault

•

System Features Unavailable

•

System Features Unavailable

•

System Voltage Out of Range

•

System Voltage Out of Range

•

System Voltage Out of Range

•

Tank Level Sensor Fault

•

Throttle Sensor Fault

•

Transmission Control Fault

•

Transmission Pressure Sensor

•

Transmission Speed Sensor

•

Transmission Temp Sensor

•

Transmission Temperature High

•

Water in Drive Fault

•

Water in Fuel

•

Wheel Forced Beyond Stop

Troubleshooting Charts

Poor Performance

Symptom

Remedy

Throttle not operating properly.

Check that the Cruise Control is disengaged.

Turn off Troll or Dock functions on DTS control pad. Refer to

Special DTS

Functionality

Damaged or improper propeller.

Replace the propeller. See an Authorized Cummins MerCruiser Diesel Repair Facility.

Excessive bilge water.

Drain and check for the cause of entry.

Содержание 92-858058K01























































































































































Результаты поиска

Содержание 92-858058K01

Отзывы:

Похожие инструкции для 92-858058K01

Бренды по названию

Популярные бренды

Mercury 92-858058K01, Руководство пользователя

Результаты поиска

Содержание 92-858058K01

Отзывы:

Похожие инструкции для 92-858058K01

Бренды по названию

Популярные бренды