manualshive.com logo in svg

Mercury 75 OptiMax, Руководство по установке, Страница: 11 / 18

Поделиться
Скачать
Mercury 75 OptiMax Скачать руководство пользователя страница 11

75/90/115  OPTIMAX

Page 11 of 18

Fuel Hose  Connection

PORTABLE FUEL TANK

Select a suitable location in boat within engine fuel line length limitations and secure tank
in place.

PERMANENT FUEL TANK

These should be installed in accordance with industry and federal safety standards which
include recommendations applicable to grounding, anti-siphon protection, ventilation, etc.

FUEL HOSE SIZE

Minimum fuel line inside diameter (I.D.) is 5/16 in. (8mm), with separate fuel line/fuel tank
pickup for each engine.

FUEL HOSE CONNECTION

Fasten remote fuel hose to fitting with hose clamp.

Water Pressure Tubing Connection (Models without SmartCraft Water PSI Gauge)

Make the water pressure gauge hose connection to this tubing as shown.

a

b

f

g

c

d

e

a -

Fuel Hose

b -

Hose Clamp – Secure Remote Fuel Hose

c -

Water Pressure Tubing (Gray Color)

d -

Water Pressure Tube – Insert into Coupler, Pull on Tube to Verify That it is
Locked

e -

Coupler (859747) – Push In on End of Coupler to Disconnect Plug or Tubing

f -

Plug (if equipped) – Remove when Making Coupler Connection

g -

Barb Hose Fitting (859731) Provided with Outboard – Install this fitting into Cou-
pler, if a Rubber Hose Connection is Required

Содержание 75 OptiMax



















Отзывы:

Нет отзывов